30266

Multiplex ROYALevo12 Manual

40
Zoom out
Zoom in
Previous page
1/57
Next page
Instructions
Page 95
14.2.2. Parameter „Trim“
N display only
change using cruciform trim buttons
4 one trim value for each flight phase
The value of this parameter indicates the extent of the
trim for this control, i.e. the magnitude and direction of
the trim correction. It is calculated from the increment
size TStep and the number of trim steps used. If the
largest increment size (3.5%) is selected, the trim travel
can be up to 70% in each direction.
14.2.3. Parameter „Step“ (trim increment)
0,5% – 1,5% – 2,5% – 3,5%
Only these four values can be selected for the trim step.
The number of trim steps is +/- 20, giving trim range
values of +/- 10%, +/- 30%, +/- 50% and +/- 70% respec-
tively
14.2.4. Parameter „D/R“ (Dual-Rates)
F can be assigned to a 3-D digi-adjustor
10% to 100%
Dual Rates enable the user to change the control sensi-
tivity of the model. For example, if the Dual Rate pa-
rameter is set to 50%, you can reduce the model’s con-
trol surface travels to half of normal by operating the
assigned switch.
14.2.5. Parameter „Trvl“
This parameter is used to determine the percentage of
full servo travel which can be obtained using the associ-
ated transmitter control.
14.2.6. Parameter „Expo“
F can be assigned to a 3-D digi-adjustor
-100% to 100%, 0% = OFF
This parameter allows you to assign an exponential
characteristic to the transmitter control. If Expo is 0%,
the transmitter control is linear in effect. Negative Expo
values have the effect that control in the area around
the centre position produces reduced control surface
travels, giving you fine control around neutral. Positive
Expo values have the opposite effect: the control sur-
face travels are greater around the centre position.
The Dual Rates function (è 14.2.3.) reduces total servo
travel, whereas Expo does not change the end-points.
This means that full travel is always available when re-
quired.
14.2.7. Parameter „Fixed value“
4 separately variable for each flight phase
F can be assigned to a 3-D digi-adjustor
-100% to 100%, 0% = OFF
This parameter is used to generate control surface trav-
els which cannot be changed by the associated trans-
mitter control.
A typical example for this function is a fixed flap posi-
tion for launching the model. When you switch on the
LAUNCH flight phase, the flaps are required to move
automatically to the launch position. In NORMAL flying
the flaps are controlled using a transmitter control (e.g.
slider F) in the normal way.
14.2.8. Parameter „Run time“ (Slow)
F can be assigned to a 3-D digi-adjustor
0.1 to 4.0 s
The run time parameter allows you to determine the
time over which a transmitter control moves from one
end-point to the other. This enables you to set up grad-
ual travel of any control system, even if it is triggered by
a switch.
Examples:
Extending retractable undercarriage slowly, so that
the process operates at scale speed.
Lowering or raising flaps slowly, so that the model does
not make any abrupt movements when you change the
flap setting.
14.2.9. Parameter „Idle“ (idle trim)
Throttle control only
This function alters the operation of the idle trim, as the
name indicates. From the graph in the H Throttle menu
you will see that the throttle trim only affects the range
up to centre (1/2-throttle). The area from centre to full-
throttle is not affected.
14.2.10. Parameter „Collective pitch“
(Coll. pitch curve)
I affects the active model only
Range +/- 100%
4 one coll. pitch curve for each flight phase
F each curve point can be assigned to a 3-D digi-
adjustor (è 10.2.2)
Adjusting the collective pitch curve for helicopters is
done in the menu H Control/Collect. Each flight
phase can have a separate curve, to adopt the curve to
each individual phase.
Example 1: Coll. pitch curve phase Hover
„Flattened“ curve between hover and collective pitch-
minimum for more sensitive hovering and landing.
… 40 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Multiplex ROYALevo12 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Multiplex ROYALevo12 in the language / languages: English as an attachment in your email.

The manual is 2,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Multiplex ROYALevo12

Multiplex ROYALevo12 User Manual - German - 58 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info