30266
34
Zoom out
Zoom in
Previous page
1/57
Next page
Instructions
Page 89
The mixer must be assigned to the appropriate
receiver outputs (è K Servo, Assignment).
The inputs must be set up correctly, i.e. the magni-
tude and direction of the servo’s movements when
the input / transmitter control is operated
(è G Mixer).
5
1
' TIP:
For modellers familiar with the
PROFI mc 3000 and 4000:
The mixer inputs of the ROYALevo are now set at the
mixer, rather than at the servo end.
The advantage is this:
The inputs are set up at a single point (è 15.), rather
than at several points (servos). This makes the task of
setting up simpler and less time-consuming. It also
means that the setting of an input can be adjusted con-
veniently when the model is in flight, using a 3-D digi-
adjustor. Careful servo calibration (è 16.1.) is also im-
portant, otherwise you may find that multiple control
surfaces do not deflect by the same amount. This would
mean, for example, that a model being landed with the
ailerons deflected up would tend to turn to one side on
the final landing approach.
13.2.2. Defining mixers
Each mixer can be assigned its own name of your
choice. This is carried out in line 3 under Name
(è 10.1.3. text input).
The next step is to assign up to 5 mixer inputs (transmit-
ter controls) of your choice; this is done in lines 1 - 5.:
Col. 1 Mixer inputs (controls)
Aileron, elevator, rudder and throttle can be
assigned as required, with or without trim.
Example line 4: "Thr -Tr" = Throttle without trim
Col. 2
Mixer switch Mix-1, Mix-2 or Mix-3
Can be used to switch the corresponding input
on or off.
"----" means that the input is always active.
Col. 3 Mixer options (è 12.2.3.)
How is the input to take effect?
Which settings are to be available when you set
up the mixer?
Where is the neutral position of the control?
13.2.3. The mixer options
„Symmetrical“
Neutral position of control: Centre
one parameter: Travel
100%
-100%
-100%
100%
Control
travel
Servo travel
TrvTrv
š
„Asymmetrical“
Neutral position of control: Centre
two parameters: Travelñ and Travelò
100%
-100%
-100%
100%
Servo travel
Control
travel
œ
„Single-sided with curve“
Neutral position of control: End-point
two parameters: Point1 and point2
100%
-100%
-100%
100%
Control
travel
Servo travel
Pt2Pt2
Pt1Pt1
›-
„Single-sided/linear with dead zone“
Neutral position of control: End-point
two parameters: Dead zone and travel
100%
-100%
-100%
100%
Control
travel
Servo travel
TrvTrv
DeadDead
The control generates a
symmetrical movement
of the servo with vari-
able travel around the
servo centre
Application sample:
Input Aileron, Elev., Flap
in mixers like AILERON+,
FLAP+, ELEVATOR +
The transmitter control
generates an asymmet-
rical movement of the
servo around the servo
centre; travel can be set
differently for both
directions.
Application sample:
Input Flap in mixers
lieke AILERON+, FLAP+
The transmitter control
generates a linear mo-
vement of the servo
from the servo centre,
with variable travel in
one direction.
Application sample:
Non-linear inputs for
compensation
(Spoiler in ELEV
A
TOR+)
The transmitter control
generates a linear mo-
vement of the servo
from the servo centre,
with variable travel in
one direction and vari-
able dead zone of the
transmit
ter control.
34


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Multiplex ROYALevo12 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Multiplex ROYALevo12 in the language / languages: English as an attachment in your email.

The manual is 2,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Multiplex ROYALevo12

Multiplex ROYALevo12 User Manual - German - 58 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info