Manual Multiplex ROYALevo12 (page 33 of 57) (English)

30266

Zoom out

Zoom in

1/57

ROYAL evo

Page 88

' TIP !

When you reach the alarm threshold that you prefer

(first audible alarm), set the threshold to 6.5 V. The

transmitter will then only emit an alarm when the bat-

tery falls to the minimum threshold. That tells you how

long you have to land your model. Don’t forget to set

“your” threshold again afterwards.

13.1.4. Parameter „Battery charge“

ü global effect

Is set to 0 mAh if the battery voltage drops below

6.5 V.

This parameter allows correction of the charge meas-

ured by the battery management system (è 8.1.).

13.1.5. Parameter „Contrast“

ü global effect

Range –8 to 8

Default setting 0

This parameter enables you to adjust the contrast of the

screen to suit the prevailing temperature conditions.

13.1.6. Parameter „ Check throttle “

I affects active model only

! Guards against the power system starting up

accidentally when you switch on the model!

Check thr ONCheck thr ON

Electric-powered models may burst into life at full throt-

tle when you switch on unless the throttle control on

the transmitter is at the idle position.

With Check THROTTLE = ON the software checks two

conditions when you switch on the transmitter:

1. Is Throttle-Cut switched off?

2. Is the THROTTLE control at idle?

The message is displayed as long as the throttle control

is not in idle position: RF radiation starts immediately,

but .due to safety reasons the throttle signal is kept in

idle.

13.1.7. Parameter “Check RF”

ü global effect

only possible with synthesizer RF module

! Safety query when transmitter is switched on!

Check RF ONCheck RF ON

Changing channels with synthesizer RF modules is rela-

tively simple, so the ROYALevo provides an additional

security query which can be activated.

With Check RF = ON the transmitter asks you whether

you really want to start transmitting on the set channel;

this it does every time you switch on. You must confirm

this by pressing a button (or by switching the transmit-

ter off again).

13.2. Sub-menu “Define mixer”

ü Defined mixers are globally available

The ROYALevo provides 14 freely definable mixers. From

this “mixer pool”, which you create over a period of time

to suit your applications and models, you can use up to

5 different mixers in one model as often as you like.

Note for helicopter pilots

These freely definable mixers are only available

for fixed-wing models. The system provides a set

of ready-made mixers for model helicopters

which cannot be changed.

Note: Predefined mixers

Mixers 1-5 are already set up as standard, but they can

be changed at any time to suit your personal require-

ments. However, please note that we cannot guarantee

that the template will work 100% correctly if you chan-

ge the standard mixers and subsequently create a new

model using a model template (è12.4.) which includes

the assigned “standard mixers”.

If you attempt to change one of these “standard mixers”

the following on-screen note appears:

13.2.1. How the freely definable mixers work

The basic principle of the ROYALevo’s freely definable

mixers is based on the proven method of working em-

ployed by the MULTIPLEX PROFI mc 3000 and 4000

series of radio control systems. A simple method of

explaining this is as follows:

We always start from the “control functions” or the ser-

vo movements. Example: aileron servo on a glider (pre-

defined mixer: AILERON+). When do we want this servo

to move?

1. When the “aileron” control is operated

(primary function)

2. When the “spoiler” function is operated

(ailerons up as landing aid)

3. When the “flap” control is operated

(up/down movement of the ailerons to trim the

wing section for thermal or speed flying)

4. When the “elevator” control is operated

(up/down movement of the ailerons to amplify the

elevator response when flying “square” aerobatic

manoeuvres => snap-flap)

We can see that the aileron servo is to be controlled by

4 transmitter controls. The “AILERON+” mixer therefore

has 4 inputs (up to 5 inputs are possible).

The mixer adds together the value of the signals gener-

ated by the individual inputs (hence also the sum sym-

bol ££ ) and passes the result to the aileron servo or

servos.

If this or any other mixer is to work correctly on a model,

the following requirements must be satisfied:

• The appropriate assignment list with the correct

transmitter controls -> inputs must be assigned to

the model (è L Setup, Assignment, Controls).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Multiplex ROYALevo12 in the language / languages: English as an attachment in your email.

The manual is 2,45 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Multiplex ROYALevo12

Multiplex ROYALevo12 User Manual - German - 58 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Multiplex ROYALevo12 Manual

Product: