30222
25
Zoom out
Zoom in
Previous page
1/32
Next page
This
is how
you
connect
the
trcnsmitter
controt
modute:
1.
The
plug
with
the marker
(coloured
sticker
on the
plug
body)
should
be connected
to one
of the hvo
transverse
connections.
The
two connections
are wired
in
parallel,
and have
the same
function.
The red
wire must
face
the
outside edge
of the
circuit
board. It
you
fit
the
plug
the wrong
way
round
the
switches
and adiustors
will
not
be assigned
correctly.
2.
Connect
the unmarked
plug
to
channel
S or 6.
Channel
5
is
useo
as
slandard,
since
thls socket is
directly
accessible
at the
receiver.
In
this
case the red
wire must
face
the centre
of
lhe
circuit
board.
lmportant:
remembe.
to
activate
the MULTlnast
svstem!
The
channel
to
which
you
have
connected
the
controi module
musr
also be
activated
under
the menu
point
DR
MN.
you
cannot
use
the
MULTlraut
system
until
you
have
carried
out this
step. Turn
bacK
lo
the section
"What
has
to be done
at the
transmitter?"
for
details
of this
proceoure.
flfl ll
thhlt,
21
Long
connecting
leads
The
cable lengths
required
in working
models
vary
widely
-
from
a few
centimetres
in
a small
ship's boat
to more
lhan
a
metre
in
a suoer_lanker.
For this reason
a
length
of
heat-shrink
sleeving
and
several 2-pin
ano
3-pin connectors
are
supplied with
theMULTlnautreceiver.
Usino rnese
items
you
can make
up the leads
yourself
to suit
your
appäcation
precisely.
lf
you
don't want
to wield
a soldering iron
and heat-gun,
the
cables supplied
can
be extended
using
screw terminal
blocks.
This is
how
to connect
a
plug:
1.
Cut
a
piece
of heat-shrink
sleeving
about 1
cm long. Remove
about 4 mm
ol insulation
from
the wlre
end.
2.
Solder the wire
to the
plug
terminal.
3. Slide the
plastic
sleeve
over
the soldered
joint
and shrink it with
a heat-gun.
You
can also
shrink the
sleeve with
a ciqarette
lighter.
but
please
be very
caretull
What
accessories
are available?
End-point
switch
set
Order No. 7
5885
End-point
switches
are
connected
to the MULTlnaul
receiver
module
and limit
the working
range
of electric
positioning
systems
(see
also:
Connecting
end-
point
switches).
Transmitter
contrcl
module
Order
No. 7
5881
Fig.
27 : Ttansmttlet
controt module
conneclion
Sttipinsulation
Soldel
Shink
@
-..
.€Ft'p
-......d
F=
rlFig.28
The EUROPA
mc
nautic
can
be
fitted
with
a second
control
module.
All
othet EUROPA
mc
transmitters
can be expanded
by
fitting
one
or two MuLTlnaut-top
control modules.
Receiver
module
Order
No. 7
5882
Extra receiver
modules
are
needed
if
you
expand
your
transmitter with
a
second control
module,
or if
you
want
to
keeo
several models
ready
lo
run.
GB-25
Manual
EUROPA
mc
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Multiplex EUROPAmc at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Multiplex EUROPAmc in the language / languages: English as an attachment in your email.

The manual is 1,97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Multiplex EUROPAmc

Multiplex EUROPAmc User Manual - German - 32 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info