30222
24
Zoom out
Zoom in
Previous page
1/32
Next page
How do
you
instalt a
MULTInautTop
module
in
an
existing
transmitter?
The transmitter
control
module
is available
under
Order
No.
7 5881
You
can either
install this
module
as a
second
unit
in an existing
EUROPA
mc
nautic
transmitter,
or
fit one
in a
EUROPA
mc
1005'
1010 and
1020
lo
exoand
the
transmitter
to
provide
MULTlnaut
Top
functions'
This
is how
you
install the
control
module
in
your
transmitter:
1. Using
a
sharp,
pointed knife
(balsa knife) cut
away
the
film
panel
over
the switch
apertures.
2. Open
the transmitter
3.
Place the
two circuit
boards
in
the
transmitter
as shown.
Do not
cüawavritm
connect
the
modules
yet;
the tlansmitter
has
lo be
cafibrated
tirst.
Description
on
page
27.
4.
The larger
of the
tlvo circuit
boards
is fixed
inside the
transmitter
using
two
screws.
The smaller
circuit
board
is fixed
lrom the
outside
with the
knurled
nuts used to
secure
the two
switches.
5. Carefully
press
the
rotary
adjustor
knobs
into
place,
pushing
them
in as
far as they
will
go (lllustration right).
When
you
rotate the
hvo
knobs they
will
click
into the centre
detent
position
so
that
you
have a
neulral
position
(motor
OFF)
which
you
can
find without
having
to
look away
from the
model
6.
To avoid
interference,
the control
unit
screening
plate
must now
be
connected
to
the transmitter
electronics.
Solder the
length of
wire
(about 4 cm
long)
in
place,
as
shown
in the
illustration
lf
the solder
is reluctant
to adhere
to
the screening
plate,
clean
the
joint
area
by scraping
it with a
small
screwdriver.
7. The transmitter
now
has to be
calibrated
This
is
the
procedure in
briel;
full details
on
Page
27:
Switch
the
üansmitter
OFF.
set all
trim
sliders
and sticks
to
centre.
Press the
E button,
hold
it
pressed
in, then
switch
on the
transmitter.
The code
numbers
1 to 6 should
now all
have a dark
background.
Belease
the
E button
again.
The
next steps
must be
repeated
tor all
four stick
planes:
a.
Trim slider
to one
end-point
(left
or
forward)
b.
Hold the
stick at
the same
end-point
for about
1
second'
c.
Trim slider
to
opposite
end-point
(right
or
back).
d.
Hold
the slick
at the
corresponding
end-point
for about
1
secono.
Once
you
have completed
this
procedure,
lhe
dark
square
behind
the code
number
for that
stick
will disappear.
Now to
calibrate
the
MULTlnaul
system
You will
need the
calibration
plug (2-pin
plug
with
lug). Use
this
plug
to
bridge
the centre
contacts
of the
MULTlnaut
channels
(5
and
6) to the
corresponding
ouler
contacts
in turn
Once
you
have
completed
this
process,
the
dark
squares
behind
the code
numbers
5 and
6 will also
disappear.
Put the
calibration
plug
away
in a sate
place.
You
will find the
plug
in the
plastic
bag
which contains
the servo
accessories
(output
arms,
mounting
screws
etc.)
Openthe
tGnsmitter
Remove
latches
Fit rotaty
knobs
Fig.23
Fig.
24 :MULT
I naut conlrcl
unit
Fig.25:
Eatlh connection
(see6.)
Placethecalibration
plug
in these
Postions.
Transmittel
elecÜontcs
ooooaaa
a
6
5
o6aa
o66a
6
Fia.26:
Position ol the
calibration
plugs
GB-24-
Manual
EUROPA
mc
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Multiplex EUROPAmc at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Multiplex EUROPAmc in the language / languages: English as an attachment in your email.

The manual is 1,97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Multiplex EUROPAmc

Multiplex EUROPAmc User Manual - German - 32 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info