561578

Multiplex COCKPIT SX Manual

79
Zoom out
Zoom in
Previous page
1/84
Next page
Operating Instructions
Page 77
ENGLIS
H
Moving to the START1 menu:
4 to MENU, r (SETUP appears),
3 to TIMER, r (START1 appears),
r
Start time for Timer 1 in minutes : seconds
The first number of the current start time flashes. Use
the 3-D digi-adjustor to set the “tens” of minutes. A brief
press r on the 3-D digi-adjustor takes you on to the
next digit.
Once you have set the “single second digits”, a brief
press r on the 3-D digi-adjustor concludes the process.
Important: the current time is stored.
The current time of Timer 1 is stored when you switch
the transmitter off. If you want the set time to start
again next time you switch on, you must first reset
Timer 1 in the INFO 2 or INFO 3 menu (long press
ª on the 3-D digi-adjustor).
If the assigned switch is at the ON position when you
switch the transmitter on again, Timer 1 immediately
resumes counting.
19.2. Timer 2
Timer 2 is ideal for recording the overall flight time. It
always starts at 00:00. The transmitter control selected
as the timer switch can start Timer 2, but it cannot stop
it again.
Timer 2 runs to a maximum of 99 minutes, 59 seconds.
Timer 2 can be started, for example, when the throttle
is advanced for the first time, when the tow-release is
operated, or when you operate the PH switch to switch
from the launch setting to normal flight.
19.2.1. Assigning a timer switch
Menu: (
TIMER) T2 SW
Example 1: starting Timer 2 using the THROTTLE
In this case the switch is assigned using the method
described in section Î 19.1.1.
Example 2: starting Timer 2 using the PH switch
Requirements:
The model must be programmed with flight phases.
Flight phase 1 is the “launch setting”, and flight phase 2
is “normal flight”.
The following example shows how to start Timer 2 (with
the stated requirements fulfilled), when you switch for
the first time from the “launch setting” to “normal flight”.
Moving to the T2 SW menu:
4 to MENU, r (SETUP appears),
3 to TIMER, r (START1 appears),
3 to T2 SW r
No switch Switch 4
Move the PH switch quickly to and fro until code num-
ber 4 appears. The hyphen following the colon indi-
cates the switch position which triggers the timer.
Switch 4 Marker Switch position
Now move the PH switch to the position which is re-
quired to trigger the timer (in our illustration Phase 2).
A brief press r on the 3-D digi-adjustor concludes the
process. The flashing ceases, and the setting is stored.
19.2.2. Stopping Timer 2, or resetting it to 00:00
Timer 2 can only be stopped or reset if it is visible in
the bottom line of the screen. There are two methods of
doing this:
In the INFO 3 display:
Pressing the 3-D digi-adjustor at this display affects
both timers.
INFO 3 display: both timers
In the INFO 4 display:
Pressing the 3-D digi-adjustor at this display only af-
fects Timer 2.
INFO 4 display: Timer 2 only
Stop timer: r brief press on 3-D digi-adjustor
Setting timer to 00:00: ª long press on 3D digi-adjustor
Phase 3
Phase 2
Phase 1
… 79 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Multiplex COCKPIT SX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Multiplex COCKPIT SX in the language / languages: English as an attachment in your email.

The manual is 1,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Multiplex COCKPIT SX

Multiplex COCKPIT SX User Manual - German - 83 pages

Multiplex COCKPIT SX User Manual - Dutch - 17 pages

Multiplex COCKPIT SX User Manual - Dutch - 149 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info