561578
78
Zoom out
Zoom in
Previous page
1/84
Next page
COCKPIT SX
Page 76
18.5. Erasing model memories
Menu: (
MEMO) DELETE
A model memory can only be used for setting up a new
model, or as destination for a copy, if its contents are
first erased.
Moving to the DELETE menu:
4 to MENU, r (SETUP appears),
3 to MEMO, r (GO TO appears),
3 to DELETE, r (0 flashes)
Current memory Selected for erasing
Use the 3-D digi-adjustor to select the model memory
which is to be erased. A brief press r on the 3-D digi-
adjustor carries out the erasure, and takes you back to
the DELETE menu.
Notes:
Only memories containing model data are offered
for erasure.
Select DELETE = 0 to delete no
memory
If you select 0 with the 3-D digi-adjustor, then confirm
your choice with a brief press r, no data will be
erased, and you are returned to the COPY menu.
You cannot erase the current memory
When you are leafing through, the number of the cur-
rent memory is not offered.
Concluding with a long press ª
This is an alternative method of concluding the pro-
cess without erasing data (wait for the confirmation
beep). In this case you are returned to the INFO 1
display.
19. Timers 1 and 2, operating time
The two timers of the COCKPIT SX can be used for the
following purposes:
TIMER 1 Î 19.1.
START = 00:00 timer runs forward (up)
START = xx:xx timer runs backward (down)
Switch, alarm, mm:ss, range
TIMER 2 Î 19.2.
runs up only, switch-operated only, hh:mm, range
OPERATING HOURS Î 19.5.
hh:mm, range
19.1. Timer 1
Probably the most common use of timers is for re-
cording the length of the motor run. In the C
OCKPIT SX
Timer 1 can be used for this, controlled by the
THROTTLE control (stick or slider).
Two operating modes are available:
a. The timer starts at 00:00 and continues to count
upward as long as the THROTTLE control is
above the selected switching threshold.
b. The timer is first set to the available motor run time
(dictated by the battery capacity / fueltank capac-
ity). As long as the THROTTLE control is above
the selected switching threshold, Timer 1 runs
downward. When 30 sec. and 20 sec. remain, you
will hear a triple / double beep. With ten seconds
to go, an alarm sounds every second. The timer
emits a trill when the pre-selected time is finished
(timer passes through zero) (Î 19.1.2.).
19.1.1. Assigning a switch
Menu: (
TIMER) T1 SW
Moving to the T1 SW menu:
4 to MENU, r (SETUP appears),
3 to TIMER, r (START1 appears),
3 to T1 SW r
No switch Switch 5 (THROTTLE)
Move the transmitter control for throttle (stick or right-
hand slider according to the set stick mode) to and fro
quickly until the code number 5 appears. The hyphen
(marker) following the colon indicates the switching
threshold you have selected.
Switch 5 Marker Switching threshold
Now move the THROTTLE control until the marker is
adjacent to the switching threshold you wish to use.
A brief press r on the 3-D digi-adjustor concludes the
process. The flashing ceases, and the setting is stored.
19.1.2. Operating Timer 1 with an alarm
Menu: (
TIMER) START1
If you set Timer 1 to count down, and if you want the
transmitter to emit an audible alarm when the set time
has elapsed, a start time must be set for this timer.
If you leave the start time at 00:00, Timer 1 runs up-
ward, and no alarm function is available.
70%
35%
15%
78


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Multiplex COCKPIT SX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Multiplex COCKPIT SX in the language / languages: English as an attachment in your email.

The manual is 1,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Multiplex COCKPIT SX

Multiplex COCKPIT SX User Manual - German - 83 pages

Multiplex COCKPIT SX User Manual - Dutch - 17 pages

Multiplex COCKPIT SX User Manual - Dutch - 149 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info