Manual MTD Zero Turn Serie Z-Force SZ (page 17 of 18) (English)

629101

Zoom out

Zoom in

1/18

English Operating Manual

Ensure that the cutting height

adjustment lever is engaged

correctly on the fixing pin.

If the cutting height adjustment

lever is released when the cutter

deck has been removed, the lever

may shoot upwards uncontrollably

due to the spring support.

 Install the cutter wheels at the

highest position.

 Raise cutter deck into a position

in which the V-belt is as

horizontal as possible between

the cutter deck and PTO clutch.

 Remove the V belt (1) from the

PTO clutch/motor pulley (2) –

fig. 20.

To do this, pull left or right side of

the V-belt backwards and then

downwards while manually

turning the engine belt pulley in

the opposite direction.

Note:

Work carefully to avoid

trapping your fingers.

 Move cutting height adjustment

lever to the lowest position .

 To disconnect the cutter deck

from the hanger, pull the split

pin (1) out of the left and right

rear cutter deck hanger (2) –

Fig. 21. In doing so, hold the

cutter deck to prevent it from

dropping on the ground.

 Push cutter deck forwards to

disconnect it from the front

hanger (3) – Fig. 21.

 Pull out the cutters from beneath

the appliance.

Assembly

Warning

If the cutting height adjustment

lever is released when the cutter

deck has been removed, the lever

may shoot upwards uncontrollably

due to the spring support.

To reinstall the cutters perform the

above steps (for removing the

cutters) in reverse order. Work

proceeds faster when you are

assisted by a second person.

Note

Following assembly, check that the

V-belt is positioned correctly and is

not twisted – Fig. 22.

Setting the cutter level

When mowing does not appear to

be parallel to the lawn the cutters

can be aligned.

Note

Before aligning the cutters check

the tyre pressure on the appliance.

Setting the side level

Fig. 14

 Move the cutter deck to

a medium height position.

 Carefully turn the outer cutters

(risk of injury) transverse to the

drive direction.

 Measure the distance between

the ground and the ends of the

two outer cutters. The result

should be the same.

If required, set the correct level

on the setting segment (1) on the

cutter deck side.

Lifting:

 Loosen nut (2) anti-clockwise

and turn nut (3) clockwise until

the level is correct.

 Retighten nut (2).

Lowering:

 Turn nut (3) anti-clockwise until

the level is correct.

 Tighten nut (2) clockwise.

Set the level from front to back.

Fig. 15

Note

Set/check the side level before this

adjustment.

 Move the cutter deck to

a medium height position.

 Carefully turn the outer cutters

(risk of injury) parallel to the drive

direction.

 Measure the distance between

the ground and the end of the

right cutter. The end of the front

cutter should be about 3.2–6 mm

lower than the end of the rear

cutter. If required, adjust the front

fixing bracket (1) equally.

Lifting:

 Loosen both nuts (3) anti-

clockwise.

 Turn both nuts (2) equally

clockwise until the level is

correct.

 Retighten both nuts (3)

clockwise.

Lowering:

 Turn both nuts (2) equally anti-

clockwise until the level is

correct.

 Tighten both nuts (3)

clockwise.

Off-season storage

Warning

Damage to mower materials

When the engine has cooled down,

store the unit in a clean and dry

room only. Always protect the

mower against rust if it is to be left

for comparatively long periods,

e.g. over the winter.

At the end of the grass-cutting

season or if the mower is not going

to be used for longer than one

month:

 Clean the mower and the grass

catcher.

 Wipe all metal parts with an oily

rag or spray them with oil to

protect them from rust.

 Charge battery with a battery

charger.

 When shutting down the unit for

the winter, remove the battery,

charge it and store in a dry/cool

location (protected from frost).

Charge the battery every

4–6 weeks as well as before re-

installing it.

 Drain the fuel tank (out in the

open air only) and service the

engine as described in the

engine handbook.

 Check tyre pressure.

 park the mower in a clean, dry

room.

Warranty

The applicable warranty conditions

in different countries are issued by

our local subsidiary company or the

importer of our products.

During the warranty period, any

malfunctions of the unit caused by

a material or manufacturing defect

will be repaired free of charge. In

the event of a warranty claim,

please contact your original dealer

or our nearest branch office.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of MTD Zero Turn Serie Z-Force SZ in the language / languages: English as an attachment in your email.

The manual is 8,64 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of MTD Zero Turn Serie Z-Force SZ

MTD Zero Turn Serie Z-Force SZ User Manual - German - 19 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

MTD Zero Turn Serie Z-Force SZ Manual

Product: