629101

MTD Zero Turn Serie Z-Force SZ Manual

16
Zoom out
Zoom in
Previous page
1/18
Next page
Operating Manual English
13
Connect the black jump lead first
to the negative terminal (–) of the
donor battery. Connect the other
clip to the frame of the engine
block of the tractor with the flat
battery (as far away from the
battery as possible).
Note
If the donor battery is installed in a
vehicle, this vehicle must not be
started during the jump starting
process.
Start the tractor with the flat
battery and actuate the parking
brake.
Disconnect the jump leads in
reverse sequence.
Tyre pressure
Warning
Never exceed the maximum
permitted tyre pressure (see tyre
wall). When pumping up the tyres,
do not stand in front of or over the
tyre.
Excessive tyre pressure reduces
the service life of the tyres. Always
check the tyre pressure before
driving.
After 5 operating hours
First engine oil change. See
engine manual for subsequent
intervals.
Use the oil channel or (optional)
quick oil drain (Fig. 16).
After 10 operating hours
Lubricate all rotating and bearing
points of the accelerator pedal
and brake pedal with several
drops of light oil.
Clean battery poles and
terminals.
Every 25 operating hours
Lubricate all blade shafts,
tensioning pulleys and
tensioning pulley holders via the
grease nipples using grease type
251H EP. Have this work carried
out by a service centre.
Lubricate the wheel bearings and
front wheel axes with 251H EP
type grease applied to their
respective grease nipples.
Remove grass and dirt around
the blade shafts beneath the
covers. Have this work carried
out by a service centre.
Lubricate the steering with
grease Type 251H EP via the
grease nipples on the steering
support. Have this work carried
out by a service centre.
Every 50 operating hours
Have dirt and grass remnants
removed from the drive gear by
a repair shop.
If required
Charge the battery
If you are not using the unit for
a prolonged period, it is recommen-
ded to take the battery out of the
unit and charge it before storage,
as well as every 2 months during
storage, and before starting up the
unit again.
Check the battery’s charged state
with a voltmeter. When the charged
state is less than 12.6 V (DC)
recharge the battery (max 12 V
at 6 A) with a battery charger in
accordance with the table.
Note
Follow the instructions in the
operating manual for your battery
charger.
Replacing fuses
Replace defective fuses only with
fuses of the same amperage.
Hydraulic expansion vessel
Fig. 17
Is used as an expansion vessel for
the hydraulic fluid during operation.
Maintenance and inspection only
by a specialist company during
annual maintenance.
Notes
– Do not check until the hydraulic
oil has completely cooled down.
– The oil level should be at least
between the base of the tank and
the mark (1).
Once per season
Lubricate all rotating and bearing
points (operating lever, height
adjustment of the cutter deck ...)
with several drops of light oil.
Clean the spark plug and check
the gap between the electrodes
or replace the plug. See engine
handbook.
The rear axles must be lubricated
with a special-purpose (water-
repellent) grease at a specialised
garage.
Have the cutting blade
sharpened or replaced in
a specialist workshop.
Note
Regularly check (when visiting your
workshop) the condition of the
mower deck V-belt.
Removing/Installing and
adjusting cutter deck
Danger
Injury hazard if engine is started
inadvertently
Protect yourself against injury.
Before carrying out any work on the
mower
– park the appliance on a level
surface,
– switch off the engine,
– withdraw the ignition key,
– switch off PTO,
– lock the parking brake.
– wait until all moving parts have
come to rest and the engine has
fully cooled,
– remove the spark plug connector
on the engine in order to prevent
the engine from accidentally
being started.
Danger
Injury hazard due to sharp cutting
blade.
Wear protective gloves.
Disassembly
Warning
The hanger/lifting mechanism is
spring-loaded and may spring
upwards as soon as the cutterdeck
is disconnected from the lifting
mechanism – work cautiously.
Voltmeter Battery
charging state
Charging
time
12.7 volts 100 % –
12.4 volts 75 %
approx.
90 min.
12.2 volts 50 %
approx.
180 min.
12.0 volts 25 %
approx.
280 min.
… 16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for MTD Zero Turn Serie Z-Force SZ at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of MTD Zero Turn Serie Z-Force SZ in the language / languages: English as an attachment in your email.

The manual is 8,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of MTD Zero Turn Serie Z-Force SZ

MTD Zero Turn Serie Z-Force SZ User Manual - German - 19 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info