629100
15
Zoom out
Zoom in
Previous page
1/18
Next page
English Operating Manual
12
Cleaning the cutting
mechanism
Danger
Injury hazard due to sharp cutting
blades
Wear protective gloves.
If the unit has more than one
cutting mechanism, moving one
cutting mechanism may cause the
other cutting mechanisms to move
as well. Caution when cleaning the
cutters.
Warning
Damage to engine
The mower must not be tilted to an
angle greater than 30°. This might
cause fuel to run into the com-
bustion chamber and could lead
to engine damage.
Raise the cutting mechanism
fully.
Clean the cutting compartment
with a scrubbing brush, hand
brush or cloth.
Cutters with cleaning nozzle
(optional)
Fig. 18
Place the appliance on an even
surface free of debris, stones, etc.,
and engage the locking brake.
1.Use a commercially available
quick-release coupling to attach
a water hose.
2.Start the engine.
3.Lower the cutters, and switch ON
for a few minutes.
4.Switch OFF the cutters and
engine.
5.Detach the water hose.
Repeat steps 1 to 5 for the second
cleaning nozzle (if provided).
At the end of cleaning (steps 1 to
5):
Raise the cutters to the top,
start the engine, and switch ON
the cutters for a few minutes to
dry them.
Maintenance
Follow the maintenance instruc-
tions in the engine handbook. At
the end of the season have the unit
inspected and serviced by a repair
shop.
Warning
Environmental hazard caused
by engine oil
Waste oil resulting from a routine
oil change should be taken to an
approved collection point or
specialist disposal company.
Batteries are an environmental
hazard
Do not throw used batteries into the
household refuse. Hand over used
batteries to your dealer or to
a waste management company.
Remove the battery before
scrapping the unit.
Using jump leads
Danger
Never bridge a defective or frozen
battery with jump leads.
Ensure that the units and the jump
lead clips do not touch each other
and that the ignitions are switched
off.
Connect the red jump lead to the
positive terminal (+) of the flat
battery and the donor battery.
Connect the black jump lead first
to the negative terminal (–) of the
donor battery. Connect the other
clip to the frame of the engine
block of the tractor with the flat
battery (as far away from the
battery as possible).
Note
If the donor battery is installed in
a vehicle, this vehicle must not be
started during the jump starting
process.
Start the tractor with the flat
battery and actuate the parking
brake.
Disconnect the jump leads in
reverse sequence.
Tyre pressure
Warning
Never exceed the maximum
permitted tyre pressure (see tyre
wall). When pumping up the tyres,
do not stand in front of or over the
tyre.
Excessive tyre pressure reduces
the service life of the tyres. Always
check the tyre pressure before
driving.
After 5 operating hours
First engine oil change.
See engine manual for
subsequent intervals.
Use the oil channel or (optional)
quick oil drain (Fig. 14).
After 10 operating hours
Lubricate all rotating and bearing
points of the accelerator pedal
and brake pedal with several
drops of light oil.
Clean battery poles and
terminals.
Every 25 operating hours
Lubricate all blade shafts,
tensioning pulleys and
tensioning pulley holders via the
grease nipples using grease type
251H EP. Have this work carried
out by a service centre.
Lubricate the wheel bearings and
front wheel axes with 251H EP
type grease applied to their
respective grease nipples.
Remove grass and dirt around
the blade shafts beneath the
covers. Have this work carried
out by a service centre.
Lubricate the steering with
grease Type 251H EP via the
grease nipples on the steering
support. Have this work carried
out by a service centre.
Every 50 operating hours
Have dirt and grass remnants
removed from the drive gear
by a repair shop.
If required
Charge the battery
If you are not using the unit for
a prolonged period, it is recommen-
ded to take the battery out of the
unit and charge it before storage,
as well as every 2 months during
storage, and before starting up the
unit again.
Check the battery’s charged state
with a voltmeter. When the charged
state is less than 12.6 V (DC)
recharge the battery (max 12 V
at 6 A) with a battery charger in
accordance with the table.
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for MTD Zero Turn Serie RZT-S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of MTD Zero Turn Serie RZT-S in the language / languages: English as an attachment in your email.

The manual is 6,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of MTD Zero Turn Serie RZT-S

MTD Zero Turn Serie RZT-S User Manual - German - 18 pages

MTD Zero Turn Serie RZT-S User Manual - Dutch - 19 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info