507836
15
Zoom out
Zoom in
Previous page
1/18
Next page
English Operating instructions for lawn tractors
12
Cutters with cleaning nozzle
(optional)
Fig. 16
Place the appliance on an even
surface free of debris, stones, etc.,
and engage the locking brake.
1.Use a commercially available
quick-release coupling to attach
a water hose. Turn on water.
2.Start the engine.
3.Lower the cutters, and switch ON
for a few minutes.
4.Switch OFF the cutters and
engine.
5.Detach the water hose.
Repeat steps 1 to 5 for the second
cleaning nozzle (if provided).
At the end of cleaning (steps 1 to 5):
Raise the cutters to the top,
start the engine, and switch ON
the cutters for a few minutes
to dry them.
Cleaning accessories
See instructions in the operating
manual for the accessories.
Servicing the vehicle
Observe the servicing guidelines
in the engine manual.
At the end of the grass-cutting
season, have the appliance checked
and serviced in a specialist workshop.
`~ìíáçå
båÖáåÉ=çáä=áë=Ü~ò~êÇçìë=
íç=íÜÉ=ÉåîáêçåãÉåí
m~ëë=çå=~åó=ï~ëíÉ=çáä=ïÜ áÅÜ=Åçã Éë=
~Äçìí=íÜêçìÖÜ=~å=çáä=ÅÜ~åÖÉ =
íç=~=ÅçääÉÅíáçå=éçáåí=çê=~= ï~ëíÉ=
Çáëéçë~ä=Åçãé~åóK
oáëâ=çÑ=éçääìíáçå=Ñêçã=Ä~ííÉêáÉë
rëÉÇ=Ä~ííÉêáÉë=Çç=åçí=ÄÉ äçåÖ=
íç=ÇçJãÉëíáÅ=êìÄÄáëÜK=
m~ëë=çå=ìëÉÇ=Ä~ííÉêáÉë=íç=~ =ÇÉ~ äÉê=
çê ~=ï~ëíÉ=Çáëéçë~ä=Åçãé ~åóK=
aáëã~åíäÉ=íÜÉ=Ä~ííÉêó=ÄÉÑçêÉ=
íÜÉ îÉÜáÅäÉ=áë=ëÅê~ééÉÇK
Using jump leads
a~åÖÉê
kÉîÉê=ÄêáÇÖÉ=~=ÇÉÑÉ ÅíáîÉ=çê=ÑêçòÉ å=
Ä~ííÉêó=ïáíÜ=àìãé=äÉ~ÇëK=
båëìêÉ=íÜ~í=íÜÉ=ìåáíë=~åÇ=íÜÉ=àìãé=
äÉ~Ç=Åäáéë=Çç=åçí=íç ìÅÜ =É~Å Ü=çíÜÉê=
~åÇ=íÜ~í=íÜÉ=áÖåáíáçåë=~êÉ=ëïáíÅÜÉÇ=çÑÑK
Connect the red jump lead to the
positive terminal (+) of the flat
battery and the donor battery.
Connect the black jump lead first
to the negative terminal (–) of the
donor battery. Connect the other
clip to the frame of the engine block
of the tractor with the flat battery
(as far away from the battery
as possible).
Note
If the donor battery is installed
in a vehicle, this vehicle must not
be started during the jump starting
process.
Start the tractor with the flat battery
and actuate the parking brake.
Disconnect the jump leads
in reverse sequence.
Tyre pressure
t~êåáåÖ
kÉîÉê=ÉñÅÉÉÇ=íÜÉ=ã~ñáãìã=éÉêãáíJ
íÉÇ=íóêÉ=éêÉëëìêÉ=Eë ÉÉ=ëáÇ É=ç Ñ íóêÉFK=
tÜÉå=éìãéáåÖ=ìé=íÜÉ=íóêÉëI=Çç= åçí=
ëí~åÇ=áå=Ñêçåí=çê=~ÄçîÉ=íÜÉ ãK
The recommended tyre operating
pressure is:
front: 0.8 bar
rear: 0.7 bar
Over-inflating reduces the longevity
of the tyres. Tyre pressure should
be checked before every journey.
After 5 operating hours
First engine oil change. See engine
manual for subsequent intervals.
Use the oil channel or (optional)
quick oil drain (Fig. 17).
After 10 operating hours
Lubricate all rotating and bearing
points of the accelerator pedal
and brake pedal with several
drops of light oil.
Clean battery terminals.
Change gear oil/gear oil filter
for the first time. This work should
be performed at a specialised
workshop.
Every 25 operating hours
Lubricate all cutter shafts, idlers,
and idler mounts with 251H EP
type grease applied to their
respective grease nipples.
This work should be performed
at a specialised workshop.
Lubricate the wheel bearings and
front wheel axes with 251H EP type
grease applied to their respective
grease nipples.
Lubricate wheels of the cutter
deck via the grease nipples using
a multi-purpose grease.
Lubricate steering shaft and stee-
ring housing via the grease nipples
using grease type 251H EP.
This work should be performed
at a specialised workshop.
Every 50 operating hours
Grass residue and other soiling
on the drive gears must be
removed at a specialised garage.
Change gear oil/gear oil filter.
This work should be performed
at a specialised workshop.
Every 2 months
For battery type 2 only – Fill battery
cells with distilled water up to 1 cm
beneath the filling aperture.
If necessary
Charging the battery
When the appliance is not used
for longer periods, we recommend
removing the battery from the appli-
ance and charging this before and
every two months during storage and
before the appliance is again put into
operation.
Note
Note the information in the operating
instructions for your battery charger.
Replace the fuse
Replace defect fuses only with
the equivalent rating.
Once a season
Apply multipurpose grease
to the teeth on the steering gear.
Lubricate the steering linkage
with a few drops of light oil.
Lubricate all moving parts and
bearing surfaces with a few drops
of oil (control levers, cutting height
adjustment).
Clean the spark plug and check
the gap between the electrodes
or replace the plug.
See engine handbook.
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for MTD CubCadet serie 2000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of MTD CubCadet serie 2000 in the language / languages: English as an attachment in your email.

The manual is 2,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of MTD CubCadet serie 2000

MTD CubCadet serie 2000 User Manual - German - 19 pages

MTD CubCadet serie 2000 User Manual - Dutch - 19 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info