507836
13
Zoom out
Zoom in
Previous page
1/18
Next page
English Operating instructions for lawn tractors
10
Preparing for operation
Park the appliance on a firm level
surface and lock the parking brake.
Conduct all work with the engine
switched off.
Remove the ignition key.
For all work on moving parts:
Open the bonnet and disconnect
the cable to the spark plug.
Set the driver seat
Fig. 7
Take your place on the driver seat.
Adjust the seat to the desired
position. Ensure that it engages
correctly!
Setting the steering wheel
Fig. 8
Take your place on the driver seat.
Move steering wheel to required
position. Ensure that it engages
correctly!
Setting the cutting mechanism
wheels (depending on model)
The cutter wheels should never
be lower than 6–12 mm above the
ground at the lowest cutter position.
The cutter wheels are not designed
to bear the loads generated by the
cutters and may have to be offset
accordingly.
Starting the engine
Sit in the driver seat.
Switch off cutter deck/accessories:
Switch off PTO and lift up cutter
deck.
Push the brake pedal down fully
or lock the parking brake.
Do not actuate accelerator pedal
(= N position).
Note
Units with hydrostatic drive are
in the “N” position when the acce-
lerator is not actuated.
Move the throttle to the middle
position (between and ).
To cold-start the engine, pull
the choke or move the accelerator
lever to .
Turn the ignition key to until the
engine is running (attempt to start
the engine for max. 5 seconds,
wait 10 seconds before attempting
to start the engine again).
When the engine is running,
set the ignition key to .
Slowly push back the choke.
Return the accelerator lever until
the engine runs smoothly.
Stopping the engine
Move the throttle to the middle
position.
Let the engine run for approx.
20 seconds.
Set ignition key to .
Remove the ignition key.
Engage the locking brake before
leaving the appliance.
Driving
a~åÖÉê
^Äêìéí=í~âÉçÑÑI=ëíçééáåÖ=ëìÇÇÉ åäóI=
~åÇ=ÇêáîáåÖ=~í=ÉñÅÉëëáîÉ=ëéÉÉÇë=ê~ áëÉ=
íÜÉ=êáëâ=çÑ=~ÅÅáÇÉåíë=~åÇ=Å ~å=Å~ ìëÉ=
Ç~ã~ÖÉ=íç=íÜÉ=ìåáíK=
kÉîÉê=ëÉíL~Çàìëí=íÜÉ=ÇêáîÉêÛë=ëÉ~í=
çê ëíÉÉêáåÖ=ïÜÉÉä=ïÜáä É=Ç êáîá åÖ K
Note
Be especially cautious when rever-
sing. Never change direction without
first stopping the appliance.
Start the engine as stated.
To ensure adequate power output,
move the throttle to .
Release the parking brake:
Press down fully the brake pedal,
and release it.
Slowly engage the drive pedal
until you have reached the speed
you want.
Stopping the appliance
Release the accelerator.
Press the brake pedal until
the appliance is stationary.
Mowing
Note
In normal mowing mode
(see Operation, Ignition lock):
Before reversing, switch off and lift
up the cutter deck.
In reverse mowing mode
(see Operation, Ignition lock):
Exercise particular care when
mowing in reverse and activate
only if absolutely essential.
Do not change direction when
the appliance is coasting or driving.
Start the engine as stated.
To ensure adequate power output,
move the throttle to .
Switch on the cutter deck.
Lower the cutters.
Release the parking brake:
Press down fully the brake pedal,
and release it.
Slowly depress the forward drive
pedal for forward direction of travel
and speed. The appliance starts
moving.
General information
When adjusting the cutting height
and driving speed, ensure that
the machine is not overloaded.
Depending on the length, type, and
dampness of the grass it may become
necessary to adjust the cutting height
and appliance speed for the optimum
grass catcher performance.
If blockages occur, reduce the driving
speed and increase the cutting height.
The best way to mow
Cut the first two rounds so the cut
grass is thrown out sideways into
the middle.
Never allow the grass to grow
too long.
Never cut the grass too low.
Drive in a straight line.
Never mow at high speed, particu-
larly when a mulching kit or grass
catcher is installed.
Mulching
Various appliances can also mulch
when fitted with the corresponding
accessories. Ask your specialised
dealer for details.
Switching off the machine
Stopping the appliance:
Release the accelerator press
brake pedal until the appliance
is stationary.
Switch off the cutter deck/acces-
sories.
Move the throttle to the middle
position.
Raise the cutters to the top.
Set the ignition key to after
twenty seconds.
Engage the locking brake before
leaving the appliance.
Remove the ignition key.
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for MTD CubCadet serie 2000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of MTD CubCadet serie 2000 in the language / languages: English as an attachment in your email.

The manual is 2,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of MTD CubCadet serie 2000

MTD CubCadet serie 2000 User Manual - German - 19 pages

MTD CubCadet serie 2000 User Manual - Dutch - 19 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info