765494

Mountfield EL 380 Li 48L Manual

35
Zoom out
Zoom in
Previous page
1/42
Next page
EN - 8
1. The motor does not
start when the switch is
pressed.
Safety key is not inserted or is inserted
incorrectly.
Insert the key (Fig. 23)
Battery is not inserted or is
inserted incorrectly. Open the hatch and check that the battery
 (Fig. 23)
Low battery. Check the battery status and
recharge if necessary (Fig. 32).
Motor start-up is slow. Press and hold the control lever
for 2-3 seconds (Fig. 25).
The thermal protection has tripped
due to overheating of the motor.
Wait for at least 5 minutes, then
restart the machine.
2. The motor is running but
the blade is stationary.
 
and remove the safety key.
Contact an authorised Technical
Assistance Centre for checks,
replacements or repairs (par. 7.3).
3. The motor shuts down
whilst working.
Battery is not inserted correctly. Open the hatch and check that the battery

Low battery. Check the battery status and
recharge if necessary (Fig. 32).
Obstructions that prevent
rotation of the blade.
Remove the safety key, put on your work
gloves and remove any grass remains or
debris from the lower part of the machine
and/or the discharge channel.
The thermal protection has tripped
due to overheating of the motor.
Wait for at least 5 minutes, then
restart the machine.
Thermal protection has tripped due to
excessive current absorption caused by:
• Excessively high grass cutting.
• Obstructions that prevent
rotation of the blade.
• Too much grass debris accumulated
in the chassis and discharge channel.
•
• Set a higher cutting height when the
grass is very tall, then set a lower
height and cut the lawn again .
• Remove the obstructions (par. 7.2.2).
• Clean the machine (par. 7.2.1)
Wait for at least 5 minutes, then
restart the machine.
4. The cut grass is
not collected in the
grass catcher.
The blade has collided with a foreign


and remove the safety key.
Inspect for damage and contact a Technical
service centre for the replacement of
the blade if necessary (par. 7.3).
The inside of the chassis is dirty. Clean the inside of the chassis to
ease the grass discharge towards
the grass catcher (par. 7.2.2).
5.  The blade is not in good condition Contact a Technical service centre for the
sharpening or replacement of the blade.
6. Excessive noise and/or
vibration is
experienced
whilst working.

the blade is damaged.

and remove the safety key.
Contact an authorised Technical
Assistance Centre for checks,
replacements or repairs (par. 7.3).
7. Battery power
reserve is low.
Severe working conditions requiring
greater current absorption.
Optimise operations (par. 7.1.1).

operating requirements.
Use a second battery or extended
battery (par. 13.2).
… 35 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mountfield EL 380 Li 48L at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mountfield EL 380 Li 48L in the language / languages: English, Italian as an attachment in your email.

The manual is 10,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info