Manual Mountfield 4155H (page 18 of 86) (English, German, Dutch, French)

765491

Zoom out

Zoom in

1/86

ENGLISH

The oil plug will be damaged if it is

tightened more to than 5 Nm.

9. Check that the gasket on the oil plug of the rear

axle is intact. See fig. 18:Y. Reinstall on the rear

axle. Tighten the filter plug to 5 Nm.

10.Draw out the oil from the deeper section of the

reservoir using an oil extractor. See fig. 20.

11.Dispose of the oil according to local

regulations.

7.5.3 Filling

The engine must never be run when the

rear clutch release lever is pushed in

and the front clutch release lever is

pulled out.

This will damage the front axle seals.

1. Fill the oil reservoir with the new oil.

If the engine is run indoors, exhaust

extraction equipment must be

connected to the engine’s exhaust pipe.

2. Check that the rear axle’s clutch release lever is

pulled out.

3. Start the engine. When the engine is started, the

front axle’s clutch release lever slides inwards

automatically.

4. Pull out the front axle’s clutch release lever.

NOTE! The oil is drawn into the system very

quickly. The reservoir must always be

topped up. Air must never be drawn in.

5. Set the accelerator pedal to the forward position

by blocking it using a wooden wedge. See fig.

21. Fill the oil reservoir by hand using new oil.

6. Run in the forward position for one minute.

7. Move the wooden wedge and set the accelerator

pedal to the reverse position. Continue filling

with oil.

8. Run in reverse mode for one minute.

9. Change driving direction once every minute as

above and continue filling with oil until the

bubbling in the reservoir stops.

10.Switch off the engine, install the oil reservoir

cover and close the engine cover.

11.Test drive for several minutes and adjust the oil

level in the reservoir.

7.6 BELT TRANSMISSIONS

After 5 hours of operation, check that all the belts

are intact and undamaged.

7.7 STEERING

The steering must be checked/adjusted after 5

hours of operation and thereafter after 100 hours of

operation.

7.7.1 Checks

Briefly turn the steering wheel back and forth.

There must be no mechanical clearance in the

steering chains.

7.7.2 Adjustment

Adjust the steering chains if required as follows:

1. Put the machine in the straight-ahead position.

2. Adjust the steering chains with the two nuts,

located under the central point. See fig. 24.

3. Adjust both nuts by the same amount until there

is no clearance.

4. Test drive the machine straight forwards and

check that the steering wheel is not off centre.

5. If the steering wheel is off centre, undo one nut

and tighten the other.

Do not over-tighten the steering chains. This will

cause the steering to become heavy and will

increase wear on the steering chains.

7.8 BATTERY

If acid comes into contact with the eyes

or skin, this can cause serious injuries.

If any part of the body has come into

contact with acid, rinse immediately

with copious amounts of water and seek

medical assistance as soon as possible.

The battery is a valve-regulated battery with 12 V

nominal voltage. The battery fluid does not need to

and cannot be checked or topped up. The only

maintenance that is required is charging, for

example after extended storage.

The battery must be fully charged

before being used for the first time. The

battery must always be stored fully

charged. If the battery is stored while

discharged, serious damage will occur.

7.8.1 Charging with the engine

See 3.3.1.

7.8.2 Charging using battery charger

See 3.3.2.

7.8.3 Removal/Installation

See fig. 5. The battery is placed under the engine

casing. During removal/installation, the following

applies regarding connection of the cables:

• During removal. First disconnect the black

cable from the battery’s negative terminal (-).

Then disconnect the red cable from the battery’s

positive terminal (-).

• During installation. First connect the red cable

to the battery’s positive terminal (+). Then

connect the black cable to the battery’s negative

terminal (-).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Mountfield 4155H in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 4,41 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Mountfield 4155H Manual

Product: