Manual Mountfield 4155H (page 17 of 86) (English, German, Dutch, French)

765491

Zoom out

Zoom in

1/86

ENGLISH EN

7 MAINTENANCE

7.1 SERVICE

We recommend that all service work is carried out

by an authorised workshop. This guarantees that

the work is performed by trained personnel and

with genuine spare parts.

7.2 PREPARATION

All service and all maintenance must be carried out

on a stationary machine with the engine switched

off.

Prevent the machine from rolling by

always applying the parking brake.

Stop the engine.

Prevent unintentional starting of the

engine by disconnecting the spark plug

cable(s) from the spark plug(s) and

removing the ignition key.

7.3 TYRE PRESSURE

Adjust the air pressure in the tyres as follows:

Front: 0.6 bar (9 psi).

Rear: 0.4 bar (6 psi).

7.4 CHANGING ENGINE OIL

Change engine oil for the first time after 5 hours of

operation, and subsequently after every 50 hours

of operation or once a season.

Change the oil more often (after 25 hours of

operation or at least once a season) if the engine

has to operate under demanding conditions or if

the ambient temperature is high.

Use oil of service grade SF or higher in accordance

with the table below.

Use oil without any additives.

Do not fill with too much oil. This can cause the

engine to overheat.

Change oil when the engine is warm.

The engine oil may be very hot if it is

drained off directly after the engine is

shut off. Therefore allow the engine to

cool a few minutes before draining the

oil.

1. Attach the clamp on the oil drainage hose. Use

a polygrip or similar. See fig. 17:V.

2. Move the clamp up 3-4 cm on the oil drainage

hose and pull out the plug.

3. Collect the oil in a collection vessel.

NOTE! Do not spill any oil on the drive belts.

4. Hand in the oil for disposal in accordance with

local provisions.

5. Install the oil drainage plug and move the clamp

back so that it clamps above the plug.

6. Remove the dipstick and fill up with new oil.

Oil volume:

4140H: 1.2 litres

4155H, 4155H 4WD: 1.4 litres

7. After filling up the oil, start the engine and idle

for 30 seconds.

8. Check to see if there is any oil leakage.

9. Stop the engine. Wait for 30 seconds and then

check the oil level in accordance with 6.2.

7.5 TRANSMISSION, OIL - FILTER

(4155H 4WD)

The oil in the hydraulic power transmission must

be checked/adjusted and changed at the intervals

given in the table below.

Type of oil: Synthetic oil 5W-50

Oil quantity when changing: approximately 3.5

litres.

7.5.1 Checking - adjusting

See “6.3”.

7.5.2 Draining

1. Run the machine at variable speeds for 10-20

minutes to heat up the transmission oil.

2. Position the machine completely horizontally.

3. Pull out both disengagement levers according to

fig. 11.

4. Place one container under the rear axle and one

under the front axle.

5. Open the oil reservoir by removing the cover.

See 16:R.

Only a 3/8” square drive may be used

for the oil plug. Other tools will damage

the plug.

6. Remove the filter plug from the rear axle. Clean

the hole and use a 3/8” square drive. Remove

the filter and allow the oil in the rear axle and

reservoir to run out. See figure 18.

7. Remove 2 drain plugs from the front axle. Use

a 12 mm socket. Allow the oil in the front axle

and pipes to run out. See fig. 19.

8. Check that the gaskets on the drain plugs of the

front axle are intact. See fig. 19. Reinstall the

plugs. Tightening torque: 15-17 Nm.

Oil SAE 10W-30

Service class SJ or higher

Action 1st time Then at

intervals of

Hours of operation

Checking – adjusting level. - 50

Changing the oil 5 200

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Mountfield 4155H in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 4,41 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Mountfield 4155H Manual

Product: