474370

Mottez A014PCAD Manual

11
Zoom out
Zoom in
Previous page
1/35
Next page
ENGLISH
You have just purchased a MOTTEZ cycle carrier, a product designed and manufactured in France.
Thank you for choosing our product, we hope you will be completely satisfied with it.
It is essential that you read these instructions before use.
Weight empty 8 kg / Maximum permitted load on cycle carrier: 45 kg or 3 bicycles.
This cycle carrier must not be used on vehicles other than those indicated in the vehicle application
list.
- For your safety and that of other users and to limit your liability, read the recommendations that we
have prepared carefully; they are not meant to be exhaustive and do not absolve you from your duty to
respect basic common sense rules.
- Keep these recommendations for use in your vehicle and ensure that they are read by any person
who installs the cycle carrier or drives the vehicle while it is installed.
- The cycle carrier may only be used for the transport of bicycles.
- Look after the straps and only use them if they are in perfect condition. Do not use them for other
purposes or with other fixing buckles.
- Check that bicycle components are properly secured (wheels, saddle, etc.). It is essential to remove
detachable accessories from bicycles (drinks bottle, removable lights, pump, etc.) or they may be lost.
- The rear load limit must be respected.
1 – Fitting the upper straps:
- Thread the two upper straps A through the upper buckles. PAY ATTENTION TO THE DIRECTION
OF INSERTION.
2 – Fitting the cycle carrier to the vehicle:
- Attach the two upper straps to the upper metal edge of the tailgate.
NEVER SUPPORT THE CYCLE CARRIER OR THE STRAPS ON A COMPOSITE (PLASTIC)
SPOILER.
- For vehicles with a frameless rear screen (glued screen) or with a wide rubber seal, use the special
adapter* (Kit ref. A027B).
- Measure the length L of the straps in accordance with the application guide for your vehicle.
3 – Adjusting the cycle carrier:
- Adjust the numbers X1 of the cycle support arm and X2 of the support bar in accordance with the
application guide for your vehicle.
- Re-tighten the handles.
- ENSURE THAT IN THE TIGHTENED POSITION THE SUPPORT ARM IS PROPERLY LOCKED IN
POSITION.
4 – Checking:
- Check that only the sleeves M are in contact with a sufficiently solid part of the bodywork (bumper,
strengthening bar, rib, window, etc.) and also check the strength of the strap attachment points.
- Ensure that no other part of the cycle carrier touches the vehicle. For safety purposes leave a gap of
several centimetres between the car body and the cycle carrier’s framework.
5 – Fitting the side straps:
- Thread the two side straps A through the buckles.
PAY ATTENTION TO THE DIRECTION OF INSERTION.
6 – Attaching the side straps to the vehicle:
- Attach the two side straps to the metal edge of the side of the tailgate.
- Ensure that the loops do not pass around the sleeves N.
7 – Fitting the lower straps:
- Pass the two lower straps A through the lower buckles. PAY ATTENTION TO THE DIRECTION OF
INSERTION.
Attaching to the vehicle: ON THE SIDE BEAMS for preference (metal part under the vehicle)
or ON THE TAILGATE only if indicated in the list of vehicles (metal tailgate rim).
NEVER SUPPORT ON OR FIX TO A PLASTIC COMPONENT.
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mottez A014PCAD at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mottez A014PCAD in the language / languages: English, German, Dutch, French, Italian, Polish, Portuguese, Swedish, Spanish as an attachment in your email.

The manual is 5,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info