744379
5
Zoom out
Zoom in
Previous page
1/16
Next page
5
ENG
The wood-burning stove must never been connected to a chimney to which a gas-burning
stove or appliance is connected.
An efficient modern stove places heavy demands on the chimney, and you should have the
chimney regularly swept and inspected by your approved chimney sweep.
The cross-sectional area of the chimney (at its narrowest point) must comply with National
and Local Building Regulations. Generally, the area needed for a Morsø wood-burning stove
installation should measure at least 175 cm2 (150 mm diameter). An over-sized chimney is
generally hard to keep warm and results in poor draft. In cases where there is an oversized
masonry chimney, it is recommended that the chimney be lined using an appropriate chimney
lining system with the correct internal diameter. With respect to the chimney termination, all
chimneys should terminate in accordance with National and Local Building Regulations. Note
that National and Local Regulations also apply with regard to the placement of chimneys and
flues in connection with thatched roofs. See the section on Draft Conditions, 1.9.
The chimney or flue system must be equipped with access doors for inspection and cleaning.
The size of the cleaning door in the chimney must at least equal to that of the cross-section-
al area of the chimney.
1.6 Fluepipe connections
Your stove is supplied ready for a top flue connection (3) the rear flue outlet is fitted with a
cover plate and is situated behind the rear heat shield/convection panel. Where a rear flue in-
stallation is required, simply knock out the steel plates in the rear heat shield/convection pan-
el. This is best done by applying gentle hammer taps immediately onto the small ”bridges”
in the circular cut-outs. Once the knock-outs have been removed unbolt the cast iron cov-
er plate and install it into the top of the stove. The flue collar can then be bolted over the rear
flue outlet using the bolts and clamps provided.
Placement of smoke tray
In some cases Morsø stoves come ready-equipped from the factory with a smoke hood (1),
as shown in the diagram. (NOTE: Not all stoves require a smoke hood). Where applicable, the
smoke hood must not be used if the stove is to be installed with a rear flue outlet (3).
Please note: During firing, the cleaning valve must always be installed correctly in the baffle
as the top cover may otherwise overheat and sustain per-
manent damage. Make sure that the baffle, smoke hood,Make sure that the baffle, smoke hood,
firebricks and the riddling grate are positioned correctly.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Morso 1452 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Morso 1452 in the language / languages: English as an attachment in your email.

The manual is 1,24 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Morso 1452

Morso 1452 Usermanual and installation guide - German - 11 pages

Morso 1452 Usermanual and installation guide - Dutch, French - 19 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info