Manual Morso 1010 (page 25 of 32) (English, Danish)

744293

Zoom out

Zoom in

1/32

2.0 Firing the stove/Using your stove

The heat output of your stove is regulated by means of the air inlets. The primary air supply, i.e.

the air which passes through the shaking grate, is controlled by the bottom draft vent, while the

secondary air supply, i.e. the air supplied to the re across the glass window, is controlled by the

top draft vent.

The stove’s rated heat output is 5,9 kW. The eciency is 84%.

Your new Morsø stove is EN-tested and recommended to be red with wood.

The stove is intended for intermittent use.

NB!

Wood is a material that contains a great deal of gas (approx. 75%). e gases are released when the wood is lit

and heated. For this reason, it is important that these gases are ignited quickly aer stoking. If the wood just

lies smouldering, especially aer re-stoking, a lot of smoke is created which, in the worst case, may cause an

explosive ignition of the gases, resulting in damage to the stove.

In order to ignite the gases that are released from the wood, and to keep clear, lasting ames during the

combustion process, it is important to let in the required quantity of oxygen (air supply) at all times. e

setting of the air supply, the method of ignition and the lighting intervals depend on the draught in the

chimney, the wind and weather, the amount of heat required, the fuel, etc. is means that it may take

some time before you get to know the correct functioning of the stove under any given circumstances.

Although you can re your Morsø stove with almost all kinds of wood, you should not re with wet

wood, or unseasoned wood. Wood ought to be stored under a roof for at least 1 year, and preferably

2 years, with free access to wind. Wood should be chopped as soon as possible aer felling if it is to

dry quickly. e wood can be used once the moisture is less than 20%. During the test, all stoves are

tested with wood with a moisture content of (16 ± 4)%.

Never use driwood as it usually has a high salt content, which damages both the stove and the

chimney. Impregnated and painted wood and chipboard emit poisonous smoke and fumes so

they should not be used as fuel either

Please note that liquid fuel may not be used in the stove.

Pieces of wood with a diameter exceeding 10 cm should always be chopped. e pieces of wood should

be short enough to be able to lie at over the layers of embers, with air at both ends. e maximum length

of fuel in the stove is 30 cm. e maximum quantity of fuel is approx. 2 kg/hour (max. 2 pieces of wood

each time you re-stoke).

e rst few times you light the stove, the re should be moderate so that the heat-resistant paint can

harden before ring more vigorously. During the hardening phase, the paint may develop obnoxious

smoke and smell the rst time it is lit, which is very normal. Make sure that the room is well ventilated

during this period.

When heating up or cooling down, the material is exposed to major temperature dierences

that may cause the stove to give o creaking sounds.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Morso 1010 in the language / languages: English, Danish as an attachment in your email.

The manual is 0,5 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Morso 1010 Manual

Product: