793834
8
Zoom out
Zoom in
Previous page
1/12
Next page
Steam Generator
RN332103 MUK Rev1
Please read and keep these instructions for future use
* Register at www.morphyrichards.co.uk/support
UK and Ireland customers only
IF YOU HAVE ANY DIFFICULTY WITH THIS PRODUCT,
INSTEAD OF TAKING IT BACK TO THE RETAILER, TRY:
1. The instruction booklet 2. Refer to www.morphyrichards.com
3. Or call our helpline: UK: 0344 871 0944, EIRE: 1800 409 119 (For UK & Eire customers only)
Register your guarantee online: www.morphyrichards.co.uk/support
We'll keep you updated with special offers, competitions and important product information.
IMPORTANT: For extra protection against limescale, use a mixture of 50%
tap water mixed with 50% deionised, distilled or demineralised water
(available at most large supermarkets).
Never use more than 50% deionised, distilled or demineralised water and
never use scented water or ironing water.
Failure to maintain your product will invalidate your guarantee.
RN332103 MUK Rev1.qxp_IB 13/03/2020 11:24 Page 1
2
The use of any electrical appliance requires the following common sense safety rules.
Please read these instructions carefully before using the product.
Important safety instructions
WARNING: Disconnect from the mains supply
before carrying out any routine maintenance.
WARNING: Misuse of the appliance could cause
personal injury.
This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities, or lack of experience
or knowledge, if they have been given supervision or
instruction concerning the use of the appliance in a
safe way and understand the hazards involved.
Children shall not play with the appliance. Cleaning
and user maintenance shall not be made by children
without supervision.
Keep the steam generator and its cord out of reach
of children less than 8 years of age at all times.
The steam generator must not be left unattended
while it is connected to the supply mains.
The steam generator must be used and rested on
a stable surface.
When placing the iron on the steam generator
base, ensure that the surface on which the base is
placed is stable.
The steam generator is not to be used if it has been
dropped, if there are visible signs of damage or it
is leaking.
The filling aperture may be opened during use, due
to the design of the system.
Do not operate with a damaged steam/supply
cord or grommet, it must be replaced by the
manufacturer, its service agent or similarly qualified
person in order to avoid a hazard.
RN332103 MUK Rev1.qxp_IB 13/03/2020 11:24 Page 2
3
Important safety instructions ........................................................
Electrical requirements ..................................................................
Steam generator overview .............................................................
Control panel overview ...................................................................
Temperature guide ..........................................................................
Before use ........................................................................................
Location ...........................................................................................
Using the Steam Generator ...........................................................
Steam boost button ........................................................................
Features ...........................................................................................
Maintenance ....................................................................................
Emptying and storing .....................................................................
Contact us .......................................................................................
Troubleshooting ..............................................................................
Guarantee ........................................................................................
Contents
2
3
4
5
5
6
6
6 & 7
8
8
9 &10
10
10
11
12
Personal safety
CAUTION - HOT:
Burns can occur from
touching hot parts, hot
water or steam, or the
iron rest plate.
WARNING: Never direct steam at
electrical components or fittings.
If in doubt about the suitability of
steam for cleaning an appliance,
contact the appliance
manufacturer for advice prior to
cleaning.
WARNING: Never touch the plug
or cable with wet hands.
WARNING: Nozzles and tools will
be hot after use. Allow to cool
before attempting to remove.
WARNING: Do not
discharge the
steam towards
people or
animals.
Danger of
scalding.
To protect against fire, electric
shock and personal injury, do not
immerse cord, plug or steam
generator in water or other liquid.
The plug should be removed from
the wall socket after use, before
cleaning, filling or changing the
accessories, or carrying out user
maintenance.
Location
Do not use or keep this product
outside.
Do not store the appliance near hot
surfaces eg. ovens or heating
appliances.
Mains cable
WARNING: A damaged or severed
mains cable fitted with a plug
should never be connected to the
mains supply. It must be
destroyed, as a damaged cable
becomes hazardous if connected
to a power socket.
Do not let the mains lead come into
contact with the hot soleplate of the
iron.
Do not allow the mains lead to
become strained.
Product safety
WARNING: Always test on an
inconspicuous area first. Never
use on materials that can not
resist high temperature, such as
dralon, natural fur etc.
Never modify the appliance in any
way.
Other safety considerations
Do not use any chemical
detergents, perfumes, alcohol or
descaler etc in water.
Repairs to electrical appliances are
only to be undertaken by trained
personnel.
Unprofessional repairs can be
dangerous for users.
Use only genuine Morphy Richards
spare parts and accessories.
The appliance must not be left
unattended while connected to the
supply mains.
This appliance is intended for
domestic use only. Misuse or use
for commercial or any other
purpose will render the guarantee
invalid.
Electrical requirements
Check that the voltage on the rating
plate of your appliance corresponds
with your house electricity supply
which must be A.C. (Alternating
Current).
If the socket outlets in your home
are not suitable for the plug
supplied with this appliance, the
plug should be removed by trained
authorised personnel and the
appropriate one fitted.
WARNING: This appliance must
be earthed.
Should the fuse in the mains plug
require changing, replace it with a
fuse of the same rating as originally
fitted.
STEAM
RN332103 MUK Rev1.qxp_IB 13/03/2020 11:24 Page 3
4
(1) Filling aperture
(2) Dirty water chamber
(3) Dirty water emptying hole
(4) Temperature indicator light
(5) Soleplate
(6) Steam trigger
(7) Iron handle
(8) Iron-to-base lock
(9) Cable support
(10) Water tank handle
(11) Detachable water tank
(12) Iron locking hook
(13) Iron rest plate
(14) Rear docking slot
(15) Control panel (see page 5)
(16) Base unit
(17) Cord storage groove
(18) Cord storage
Steam generator overview
4
5
17 18
67
10
15
16
8
9
11
12 1413
1 3
2 3
1
2
17
RN332103 MUK Rev1.qxp_IB 13/03/2020 11:24 Page 4
5
Control panel overview
Descale indicator (19)
When the system requires cleaning, the descale
indicator (19) will illuminate. When this happens,
follow the instructions under ‘Maintenance’ on
page 9.
Low water indicator (20)
This indicator will illuminate when there is
insufficient water in the tank to produce steam.
On/Off power indicator (21)
This indicator illuminates when the unit is turned
on, and extinguishes if the appliance is turned off
or has entered auto shut-off mode after not being
used for 10 minutes.
On/Off power button (22)
Connect to a mains outlet and press the On/Off
power button (22). The button will illuminate and
the low steam level indicator (24a) will flash. To
turn off, press and hold the On/Off power button
for 3 seconds.
Steam level select button (23)
Press the steam level select button (23) to toggle
through the steam levels. Each press cycles the
level from low to medium to high, back to low and
so forth.
Steam level indicators (24)
Press the steam level select button (23) to adjust
the steam level. The steam level selected will be
displayed by illumination of the relevant steam
level indicator: low (24a), medium (24b) or high
(24c). See step 5 of ‘Using the Steam Generator’
on page 7.
Temperature guide
Garment symbol (120°C Max) Cool (160°C Max) Warm (210°C Max) Hot MAX setting
Temperature
Do not iron
Fabric Nylon,
Acetates,
synthetic fabrics
Wool,
Polyester mixtures
Cotton,
Linen Rayon,
Rayon mixtures
Ironing Iron on wrong side,
if moisture
required, use
damp cloth
(not Acetate)
Fabrics requiring
this setting usually
require steam
pressing.
Steaming
Without steam
Steam level setting
(see step 5 of
‘Using the Steam
Generator’ on
page 7)
No steam
(see ‘Dry ironing’
on page 8)
Low Medium / High High
Low water
indicator
20
Low steam level
indicator 24a Medium steam
level indicator 24b High steam level
indicator 24c
Descale
indicator 19
On/Off power
indicator 21
On/Off power
button 22
Steam level
select button
23
IntelliTemp setting
RN332103 MUK Rev1.qxp_IB 13/03/2020 11:24 Page 5
6
Using the Steam Generator
Plug the appliance into a mains outlet. Press the
On/Off power button (22), it will beep and the
low steam level indicator (24a) will flash.
2
Remove the detachable water tank (11) by pulling
the water tank handle (10), and fill with water
through the filling aperture (1) to the max fill line
.
Replace the water tank.
IMPORTANT: Never fill the dirty water chamber
(2)
.
IMPORTANT: FOR EXTRA PROTECTION
AGAINST LIMESCALE, USE A MIXTURE OF
50% TAP WATER MIXED WITH 50%
DEIONISED, DISTILLED OR DEMINERALISED
WATER (AVAILABLE AT MOST LARGE
SUPERMARKETS).
NEVER USE MORE THAN 50% DEIONISED,
DISTILLED OR DEMINERALISED WATER AND
NEVER USE SCENTED WATER OR IRONING
WATER.
Never use battery topping up fluid or water
containing any substances like starch, sugar,
fragrant additives or defrosted water from a
refrigerator.
NOTE: Please see point 2 of ‘Exclusions’ on page 12.
Re-filling during use
If the water level is too low, the unit will not
produce steam. If this happens, refill the
detachable water tank (11) with water.
1
Remove any protective cover from the soleplate (5) and the base unit (16).
Unwind and straighten the power cord and steam supply cord.
Locate the steam generator horizontally on the iron rest plate of your ironing board (if large enough) or on a
heat resistant stand at the same height as your ironing board or below it. Always ensure the steam
generator is on a firm surface when ironing.
WARNING: Do not use the product on a surface which could be damaged by heat or steam such as
a worktop or a polished wood surface.
If in doubt, contact Morphy Richards.
Location
Before use
RN332103 MUK Rev1.qxp_IB 13/03/2020 11:24 Page 6
8
Dry ironing
To use your steam generator as a dry iron only,
follow steps 2, 3 and 4 of ‘Using the Steam
Generator’ on pages 6 and 7. You do not need to
put water in the tank or select a steam level.
Press
the steam trigger
(6) at least once every 10
minutes, or the product will automatically turn
off.
Auto shut-off
If
the iron
is not used for 10 minutes, the product
will automatically turn off for safety and to save
energy, and a beep will be heard.
To restart, press the On/Off power button (22)
(see step 2 of ‘Using the Steam Generator’ on
page 6) and wait for the temperature to rise
again.
Steam function
During steaming, small amounts of water may be
ejected from the soleplate
(5)
. This is normal and
can be avoided by using the steam for short
amou
nts of time and only when the iron is at the
correct temperature (the temperature indicator
light (4) on the iron illuminates when ready).
Sudden jolts of the boiler unit can also cause
water droplets on the soleplate; therefore, do not
move the base unit during ironing.
We recommend for first time ironing that you
iron over an old towel.
Vertical steam
Vertical steam is useful for removing creases
from hanging clothes, curtains, upholstery, etc.
Hold the iron between 1cm and 2cm away from
the item and press the steam trigger
(6)
twice in
quick succession for a longer boost of steam. To
turn the steam boost off, press the steam trigger
again.
WARNING: Do not use the vertical steam
feature on clothes that are being worn.
Features
6
Steam boost button
The steam boost function is ideal for relaxing the
fibres of tougher fabrics (like jeans and linen) and
getting rid of those stubborn, hard to reach creases.
To produce a steam boost during ironing, simply
press the steam trigger (6) twice in quick
succession. To turn this off, press the steam trigger
again.
To conserve water in the tank, we recommend you
switch off the steam boost when the iron is not in
use.
6
RN332103 MUK Rev1.qxp_IB 13/03/2020 11:24 Page 8
RN332103 MUK Rev1 03/20
Y
our standard 1 year guarantee is extended for an
additional 2 years when you register the product within 28
days of purchase with Morphy Richards. If you do not
register the product with Morphy Richards within 28 days,
your product is guaranteed for 1 year. To validate your 3
year guarantee register with us online at
www.morphyrichards.co.uk
Or call our customer registration line
UK 0344 871 0242
IRE 1800 409 119
N.B. Each qualifying product needs to be registered with
Morphy Richards individually.
Please note that the 3 year guarantee is only available in
the UK and Ireland. Please refer to the 1 year guarantee
for more information.
It is important to retain the retailers receipt as proof of
purchase. Staple your receipt to this back cover for future
reference.
Please quote the following information if the product
develops a fault. These numbers can be found on the base
of the product.
Model no.
Serial no.
All Morphy Richards products are individually tested before
leaving the factory. In the unlikely event of any appliance
proving to be faulty within 28 days of purchase, it should
be returned to the place of purchase for it to be replaced.
If the fault develops after 28 days and within 12 months of
original purchase, you should contact the Helpline number
quoting Model number and Serial number on the product,
or write to Morphy Richards at the address shown.
You may be asked to return a copy of proof of purchase.
Subject to the exclusions set out below (see Exclusions),
the faulty appliance will then be repaired or replaced as
appropriate and dispatched usually within 7 working days
of receipt.
If, for any reason, this item is replaced or repaired during
the 1 year guarantee period, the guarantee on the new
item will be calculated from original purchase date.
Therefore it is vital to retain your original till receipt or
invoice to indicate the date of initial purchase.
To qualify for the 1 year guarantee, the appliance must
have been used according to the instructions supplied.
For example, water should be emptied after each use.
Morphy Richards shall not be liable to replace or repair the
goods under the terms of the guarantee where:
1The fault has been caused or is attributable to accidental
use, misuse, negligent use or used contrary to the
manufacturer’s recommendations or where the fault has
been caused by power surges or damage caused in transit.
2The fault is caused by limescale build-up.
3The cables are damaged due to wrapping too tightly or
excessive kinking.
4The appliance has been used on a voltage supply other
than that stamped on the products.
5Repairs have been attempted by persons other than our
service staff (or authorised dealer).
6The appliance has been used for hire purposes or non
domestic use.
7The appliance is second hand.
8Morphy Richards reserves the right not to carry out any
type of servicing under the guarantee at its discretion.
This guarantee does not confer any rights other than those
expressly set out above and does not cover any claims for
consequential loss or damage. This guarantee is offered
as an additional benefit and does not affect your statutory
rights as a consumer. Morphy Richards products are
intended for household use only. See usage limitations
within the location safety instructions.
Morphy Richards has a policy of continuous improvement
in product quality and design. The company, therefore
reserves the right to change the specification of
its models at any time.
For electrical products sold within the
European Community. At the end of the
electrical products useful life, it should not be
disposed of with household waste.
Please recycle where facilities exist. Check
with your Local Authority or retailer for
recycling advice in your country
Exclusions
Registering your 3 year
guarantee
Your 1 year guarantee
Disclaimer
The After Sales Division
Morphy Richards Ltd
Mexborough,
South Yorkshire,
England, S64 8AJ
IF YOU ARE HAVING A PROBLEM
WITH ONE OF OUR PRODUCTS,
CALL OUR HELPLINE:
UK: 0344 871 0944
EIRE: 1800 409 119
SPARES: 0344 873 0710
RN332103 MUK Rev1.qxp_IB 13/03/2020 11:24 Page 12
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Morphy Richards 332103 - Speed Steam Pro at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Morphy Richards 332103 - Speed Steam Pro in the language / languages: English as an attachment in your email.

The manual is 1.43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info