Manual Morco GB24 Series II (page 25 of 36) (English)

653301

Zoom out

Zoom in

1/36

SECTION 7 - ROuTINE SERvICINg INSTRuCTIONS

7.1

SERVICING SCHEDULE

Fortheverylatestcopyofliteratureforspecication,maintenancepracticesandpartsreplacement,visitourwebsitewww.morcoproducts.co.uk

where you will be able to download the relevant information.

WARNING. Always turn OFF the gas supply at the gas service cock, and switch OFF and disconnect the electricity supply to

the appliance before servicing.

Combustion testing must be carried out by a competent person using a combustion analyser conforming to BS7927.

Toensurethecontinuedsafeandefcientoperationoftheapplianceitisrecommendedthatitischeckedatregularintervalsand

serviced as necessary. The frequency of servicing will depend upon the installation condition and usage but should be carried out at

least annually.

ItisthelawthatanyserviceworkmustbecarriedoutbyaGasSafeRegisteredEngineer,orinothercountriesaqualiedand

competent Gas Installer.

INSPECTION

1. Light the boiler and carry out a pre-service check, noting any

operational faults.

2.Checktheueterminal(andterminalguardiftted)is

undamaged and clear of any obstruction.

3. Check all water and gas joints for signs of leakage. Remake

any suspect joints ensuring a gas tightness check is carried

outifapplicableandthewatersystemiscorrectlyrelled,

vented and re-pressurised.

CLEANING PROCEDURE

Note. In order to carry out either servicing or replacement of

components the boiler upper and lower front panels must

be removed. Refer to Frame 7.2.

1. Clean the main burner. Refer to Frame 7.4.

2. Cleantheheatexchanger&condensatetrap/siphon.Referto

Frames7.5&7.6.

Check the main injector for blockage or damage. Refer to

Frame 7.3.

4. Checkthattheueterminalisunobstructedandthattheue

system is sealed correctly.

The cleaning procedures are covered more fully in Frames 7.3-7.7

and MUST be carried out in sequence.

IMPORTANT.

5. After completing the servicing or exchange of components

always test for gas tightness.

6. When work is complete the front panels MUST be correctly

retted,ensuringthatagoodsealismade.

Do NOT OPERATE the boiler if the upper front

panel is not tted.

7. If, for any reason, the condensate trap/siphon has been

removedensurethetrapisrelledwithwaterbefore

reassembling.

8. Check the gas consumption if on metered installations.

Checkcombustionbyconnectingtheuegasanalysertothe

uegassamplingpointasshowninthediagramandmeasure

CO&CO

. (Refer to Section 10, page 35).

If the CO/CO

ratio is greater than 0.004 AND the integrity of

thecompleteuesystemandcombustioncircuitsealshave

beenveriedandtheinletgaspressurehavebeenveried,

then contact Morco.

Flue Sampling Point

Air Sample

Point

Ensure all caps and seals

are re-fitted after use

GENERAL

Please Note: During routine servicing, and after any maintenance

or change of part of the combustion circuit, the following must be

checked:

- Theintegrityoftheuesystemandtheueseals,

- The integrity of the boiler combustion circuit and the relevant seals

- The operational (working) gas inlet pressure at maximum rate.

Turn on one or more DHW taps.

- The combustion performance.

COMPETENCE TO CARRY OUT THE CHECK OF

COMBUSTION PERFORMANCE

Please Note: BS6798:2009Specicationforinstallationand

maintenanceofgas-redboilersofratedinputnotexceeding70kW

net advises that:

- The person carrying out a combustion measurement should have

beenassessedascompetentintheuseofauegasanalyserand

the interpretation of the results.

- Theuegasanalyserusedshouldbeonemeetingthe

requirements of BS7927 or BS-EN50379-3 and be calibrated in

accordance with the analyser manufacturers requirements, and

- Competence can be demonstrated, for example, by satisfactory

completion of the CPA1 ACS assessment (UK Only), which

covers the use of electronic portable combustion gas analysers in

accordance with BS7967, Parts 1 to 4.

SERVICE MODE

To access the service mode:

Using the central heating potentiometer, starting from the 11 o’clock

position, move the thumb piece to the maximum position, back to the

11o’clockpositionandthennallynishatthemaximumposition.

The letter “S” will now be displayed.

To toggle to maximum DHW output move the thumb piece up to

the 11 o’clock position and then back to maximum. A minimum of 3

seconds will reset the boiler back to normal mode.

We have this Boiler fitted in our Caravan and not had a trouble till we had the boiler serviced since then the boiler will deal with the hot water but if you put it onto timer for the central heating the boiler comes in and when it gets to temperature goes out but then when the temperature drops the boiler does not come back in and shows L-2 which means it’s locked out please advice what can be the trouble thankyou Submitted on 10-11-2021 at 19:52
Reply Report abuse
- condensing tack requires cleaning maybe Answered on 25-11-2023 at 18:25
  Vote up Report abuse
Je voudrais savoir pourquoi s affiche sur l écran de contrôle F 9 qui clignote. Et pas d eau chaude. Submitted on 29-6-2021 at 18:11
Reply Report abuse
Hot water working but no heating and no fault codes Submitted on 12-4-2021 at 18:39
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Morco GB24 Series II in the language / languages: English as an attachment in your email.

The manual is 6,25 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Morco GB24 Series II Manual

Product: