653301

Morco GB24 Series II Manual

24
Zoom out
Zoom in
Previous page
1/36
Next page
24
SECTION 6 - COMMISSIONING INSTRUCTIONS
6.5 FINAL CHECKS
Re-light and test for gas soundness.
Set the CH and DHW temperature knobs to the desired settings.
Ensure that the integral timer and/or room thermostat are set to
the required settings.
6.6 HANDING OVER
After completing the installation and commissioning of the system
the installer should:
• Hand the Users Instruction to the owner and emphasise their
responsibilities under the relevant national regulations.
• Explain and demonstrate the lighting and shut down
procedures.
• Explain the operation of the boiler and the use and
adjustment of the system controls to ensure the greatest
possible fuel economy, consistent with the owners heating
and hot water requirements.
• Advise the user of the precautions necessary to prevent
damage to the system and to the building in the event of the
system remaining in operation during frosty condition.
• Explain the function of the boiler fault mode. Emphasise that
if a fault is indicated, refer to Fault Codes in the User Guide.
• Explain and demonstrate system controls, integral timer
functions and boiler reset procedure.
IMPORTANT - Stress the importance of an annual service by
a competent gas registered engineer.
THE DISPLAY
The user control has one neon and one display to inform the
user about the status. The display will show the status of the
boiler.Theneonwillshowthestatusoftheame.Ifnoame
isdetectedtheneonisoff.Whentheameisdetectedthe
neon will be lit permanently.
Below is a list with display function in normal operation.
0 Standby, no demand for heat present.
Boiler is active for central heating.
Boiler is active for domestic hot water.
Boiler is heating up the plate heat exchanger.
CH circuit water less than 5ºC.
Below is a list with display in fault condition. If the display is
ashingwith“L”or“F”withalternatenumbers/lettersreferto
page 32.
Boilerisinlockoutforaspecicerror.Displaywillbe
blinking, alternating with a number or letter to show which
error is detected.
Boilerhasafaultforaspecicerror.Displaywillbe
blinking, alternating with a number or letter to show which
error is detected.
Service mode
… 24 …


Need help? Post your question in this forum.

Forumrules
1

Forum

morco-gb24-series-ii

Reset search

  • We have this Boiler fitted in our Caravan and not had a trouble till we had the boiler serviced since then the boiler will deal with the hot water but if you put it onto timer for the central heating the boiler comes in and when it gets to temperature goes out but then when the temperature drops the boiler does not come back in and shows L-2 which means it’s locked out please advice what can be the trouble thankyou Submitted on 10-11-2021 at 19:52

    Reply Report abuse

  • Je voudrais savoir pourquoi s affiche sur l écran de contrôle F 9 qui clignote. Et pas d eau chaude. Submitted on 29-6-2021 at 18:11

    Reply Report abuse

  • Hot water working but no heating and no fault codes Submitted on 12-4-2021 at 18:39

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Morco GB24 Series II at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Morco GB24 Series II in the language / languages: English as an attachment in your email.

The manual is 6,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info