653301

Morco GB24 Series II Manual

11
Zoom out
Zoom in
Previous page
1/36
Next page
11
section 3 - tecHnicAL DAtA
DATA PLATE
3952.5
2.5
from case
700
Side
flue
dim. A
285
86.5
17
155
CH FLOW
DHW OUTLET
COND. DRAIN
GAS INLET
DHW INLET
CH RETURN
PRV
43.5 65
28.5 28.5
60.6 75 37.556.4
Underside View - Dimensions to Wall
W A L L
W A L L
99
103 99
99 103
*Required for maximum ow rate. Boiler operates down to 2 l/min DHW delivery
Table 3 - Performance Data - Domestic Hot Water
BOILER DIMENSIONS, SERVICES & CLEARANCES
Theboilerconnectionsaremadeontheboilerbulkheadttings.
The following minimum clearances must be maintained for
operation and servicing.
Additional space will be required for installation, depending upon
site conditions.
Side and Rear Flue
a. Providedthattheueholeiscutaccurately,e.g.withacore
boringtoolorholecuttertheuecanbeinstalledfrominside
the dwelling where wall thicknesses do not exceed 600mm
(24”). Where the space into which the boiler is going to be
installedislessthanthelengthofuerequiredtheuemust
bettedfromtheoutside.
Installation from inside ONLY
b. If a core boring tool or hole cutter is to be used inside the
dwelling the space in which the boiler is to be installed
must be at least wide enough to accommodate the tool.
In either of the above cases safe external access is


Front clearance
The minimum front clearance when
built in to a cupboard is 5mm from
the cupboard door but 450mm overall
clearance is still required, with the
cupboard door open, to allow for
servicing.
* Bottom clearance
Bottom clearance after installation
can be reduced to 5mm.
This must be obtained with an
easily removable panel, to enable
the consumer to view the system
pressure gauge, and to provide
the 100mm clearance required for
servicing.
Max 30kW
Max 24kW
2.Foruelengthsrequiring“D”packextensions(RSF341),theuemustinclineby26mmper1Metreofuelength.
… 11 …


Need help? Post your question in this forum.

Forumrules
1

Forum

morco-gb24-series-ii

Reset search

  • We have this Boiler fitted in our Caravan and not had a trouble till we had the boiler serviced since then the boiler will deal with the hot water but if you put it onto timer for the central heating the boiler comes in and when it gets to temperature goes out but then when the temperature drops the boiler does not come back in and shows L-2 which means it’s locked out please advice what can be the trouble thankyou Submitted on 10-11-2021 at 19:52

    Reply Report abuse

  • Je voudrais savoir pourquoi s affiche sur l écran de contrôle F 9 qui clignote. Et pas d eau chaude. Submitted on 29-6-2021 at 18:11

    Reply Report abuse

  • Hot water working but no heating and no fault codes Submitted on 12-4-2021 at 18:39

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Morco GB24 Series II at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Morco GB24 Series II in the language / languages: English as an attachment in your email.

The manual is 6,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info