646340

Morco FEB-24ED Manual

15
Zoom out
Zoom in
Previous page
1/20
Next page
15
5.1 BOILER PACKAGING
The boilers are supplied in dierent packagings:
- Boiler
- Flue system (separate packaging)
5.2 FITTING THE BOILER.
- Decide where the boiler is to be xed on the wall
taking into account the installation requirements
detailed in section 4.2 and the clearances and dimen-
sions described in the the technical data.
The centres for the hanging strap xing are 85mm
below the top of the boiler casing, see g below.
The ue pipe centre is 213mm above the hanging
strap centres. NOTE: a fall of about 2º - 3º should be
allowed on the ue pipe to stop water ingress into the
boiler.
A screw xing should be made on the bottom rail of
the boiler to secure it during transport.
5.3 WIRING INSTRUCTIONS
Warning: observe the usual precautions to ensure
that the electricity supply is isolated before com-
mencing any installation or service work.
- The appliance is tted with a 3 amp. fused 3 pin
plug for use with 230 V~50Hz. It should be tted to a
shuttered socket outlet complying with BS 1363
WARNING: THIS APPLIANCE MUST BE
EARTHED.
ROOM THERMOSTAT:
This appliance may be used in conjunction with an
external room thermostat.
The volt
age between the contacts of the room ther-
mostat is 24V (normally closed). Any 24V controls
may be used, but gold contacts are recommended.
DO NOT under any circumstances use a mains sup-
ply to the stat as you will blow the P.C.B. in the boil-
er. Only voltage free switching stats should be used.
Connection of a room thermostat (optional) .Proceed
as follows:
Unscrew the screw (A) as it shows gure 1, open
the bottom cover, where the connector of the room
thermostat is placed.
Press out the plastic disc (B) using a screwdriver to
form a hole so you can pass through the wires of the
room stat.
Replace cover.
The room thermostat must be installed on a wall
which is free from any objects and free from direct
contact with either sunlight or draughts.
External Probe connection Type 10K-25ºC, B3435
1% (25-85) (optional).
Press out the plastic disc (B) using a screwdriver to
form a hole so you can pass through the wires of the
external probe.
Conect the external probe wires to the free holes
with red wires in the other side..
Congurate the external
probe curve in instalation
menu.
5.- INSTALLATION INSTRUCTIONS
Figure 1
A
B
1
2
3
Black
Wires
Thermostat
External Probe
TMV2
3
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Morco FEB-24ED at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Morco FEB-24ED in the language / languages: English as an attachment in your email.

The manual is 3,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info