216162
41
Zoom out
Zoom in
Previous page
1/47
Next page
EN-41
POWER
O f f
Steady r ed
Blinking
red/green
S TA TUS
O f f
O f f
Blinking
orange
Blinking
g r een
Steady r ed
O f f
Steady
or
Blinking
Solution
Connect the power co r d to the p r ojecto r .
Plug the power co r d into a wall outlet.
If any objects a r e blocking the air inlet or outlet grille, r emove them and carry
out the following.
1. Unplug the power co r d f r om the wall outlet.
2. Make su r e that the p r ojector has cooled o f f.
3. Plug the power co r d into the wall outlet.
4. P r ess the POWER button.
If any objects a r e blocking the air inlet or outlet grille, r emove them.
Don't expose the air outlet grilles to hot air emitted f
Check wheather the filter is clogged with dirt and dust.
Clean the filter, if clogged. (See page 40.)
r om a heating appliance.
After the S TA TUS indicator stops blinking, p r ess the POWER button.
If you unplug the power co r d while the fan is r otating, the lamp may not tu r n on about 1 minute when
you plug the power co r d next time.
The lamp can't tu r n on again for 1 minute after it goes out.
P r ess the POWER button several times.
Replace the lamp. (The lamp is at the end of its life.)
Attach the lamp cover on the bottom.
Unplug the power co r d f r om the wall outlet and contact your deale r .
Troubleshooting
Before asking for repair of the projector, check the following. If the symptom persists, stop using the projector, be
sure to unplug the power plug, and then contact your dealer.
No image appears on the screen.
Problem
Power can not be
turned on.
No image appears on
the screen.
Power turns off.
Solution
Check whether the indicators are on or off and how they are lightning.
Cancel the AV mute by pressing the MUTE button.
Check that the lens cap is removed.
It may take about 1 minute for the lamp to light up.
The lamp fails to light up on rare occasions. In such a case, wait for a few minutes
and then try again.
If the projector was turned off before the lamp was cooled down suf ciently last time,
the fan may start rotating and the POWER button may not work after the power cord
is plugged. After the fan stops rotating, press the POWER button to turn back on the
POWER indicator.
Set SCART INPUT in the FEATURE menu to OFF. (See page 25.)
Check that the intake vent is clean.
Check that the lamp cover is closed. (See page 39.)
Check that the cables connected to the external devices are not broken.
When an extension cable is being used, replace it with the supplied cable for check.
When images are displayed correctly, add an RGB signal amplifier to the extension
cable.
This problem may occur when the intake vent and/or exhaust vents are blocked. (In
such a case, the STATUS indicator brinks orange.)
J
Remove the objects blocking the intake vent and/or exhaust vents and then carry
out the following procedure.
1. Wait for the intake fan and/or exhaust fan to stop. (Wait until the STATUS
indicator goes out.)
2. Unplug the power cord from the wall outlet.
3. Wait about 10 minutes.
4. Plug the power cord into the wall outlet.
5. Press the POWER button.
When the STATUS indicator is steady red, it is indicating that the lamp should be
replaced. Replace the lamp in this case.
Check that AUTO POWER OFF has been set to OFF.
If the lamp has deteriorated, it may go out after a while it illuminates.
41


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi wl2650u at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi wl2650u in the language / languages: English as an attachment in your email.

The manual is 8,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info