216162
39
Zoom out
Zoom in
Previous page
1/47
Next page
EN-39
To replace the lamp:
1. Unplug the power cord.
2. Loosen the screw (a) using a Phillips screwdriver (+), and
remove the lamp cover (b).
3. Loosen the screws (c) using a Phillips screwdriver (+).
4. Pull the handle.
5. Pull out the lamp box by the handle while holding the
projector.
Pull the lamp box out of the projector slowly. If it is
pulled out quickly, the lamp may break scattering glass
fragments.
Do not spill liquid on the removed lamp box or do not
place it near any fl ammable object or where children
can reach to prevent injury or fi re.
6. Load a new lamp box securely into the projector in the right
orientation.
7. Put the handle back to the original position.
Make sure that the handle is locked.
8. Tighten up the screws (c) using a Phillips screwdriver (+).
9. Tighten up the screw (a) using a Phillips screwdriver (+) to
secure the lamp cover.
Reset of the lamp operation time
Plug in the power cord and reset the lamp operation time by
holding down the
W
,
X
, and POWER buttons on the control
panel at the same time about three seconds.
Important:
Unless these 3 buttons are pressed at the same time, the lamp operation time isn’t reset.
Make sure that the STATUS indicator is lit twice and the lamp operation time is reset successfully.
The projector doesn’t turn on if the lamp cover isn’t attached securely.
Be sure to reset the lamp operation time whenever you replace the lamp.
Do not reset the lamp operation time unless you replace the lamp.
When removing the lamp from the ceiling-mounted projector
When removing the lamp from the ceiling-mounted projector, use the lamp replacement tray packed with the
projector or option lamp to prevent glass fragments from scattering.
Assemble the lamp replacement tray according to the procedure shown on it.
(a)
(b)
(c)
(c)
(a)
Important:
The lamp is fragile. If it is broken, be careful not to cut yourself with glass fragments.
Caution:
This projector uses a lamp that contains mercury. Disposal of the lamp or the projector
with the lamp may be regulated due to environmental considerations. For disposal or
recycling information, please contact your local authorities or the Electronic Industries
Alliance: www.eiae.org. (For the U.S. only.)
1. Follow steps 1 to 4 shown above.
2. Attach the lamp replacement tray to the projector as shown
in the fi gure.
3. Secure the lamp replacement tray on the projector using
the tape packed with the tray.
4 Pull out the lamp box by the handle while holding the
projector.
Hold the lamp replacement tray to prevent glass
fragments from scattering.
Don’t put the lamp directly on the lamp replacement
tray because it may fall.
5. Detach the lamp replacement tray together with the
removed lamp.
Tape
Replacing the lamp (continued)
39


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi wl2650u at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi wl2650u in the language / languages: English as an attachment in your email.

The manual is 8,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info