549869
60
Zoom out
Zoom in
Previous page
1/69
Next page
EN-60
Troubleshooting
Before asking for repair of the projector, check the following. If the symptom persists, stop using the projector, be
sure to unplug the power plug, and then contact your dealer.
No image appears on the screen.
Problem Solution
Power can not be
turned on.
• Checkwhethertheindicatorsareonoroffandhowtheyarelightning.
POWER STATUS Solution
Off Off
• Connectthepowercordtotheprojector.
• Plugthepowercordintoawalloutlet.
Steady red
Off
• Ifanyobjectsareblockingtheintakeorexhaustvents,removethemand
carry out the following.
1. Unplug the power cord from the wall outlet.
2.
Make sure that the projector has cooled off.
3.
Plug the power cord into the wall outlet.
4.
Press the POWER button.
Blinking orange
• Ifanyobjectsareblockingtheintakeorexhaustvents,removethem.
• Don’texposetheexhaustventstohotairemittedfromaheatingappliance.
Blinking green
• AftertheSTATUSindicatorstopsblinking,pressthePOWERbutton.
• Ifyouunplugthepowercordwhilethefanisrotating,thelampmaynotturnon
about 1 minute when you plug the power cord next time.
• Thelampcan’tturnonagainfor1minuteafteritgoesout.
• PressthePOWERbuttonseveraltimes.
Steady red
• Replacethelamp.(Thelampisattheendofitslife.)
Blinking
red/green
Off
• Attachthelampcoveronthetop.
Steady
or
Blinking
• Unplugthepowercordfromthewalloutletandcontactyourdealer.
No image appears on
the screen.
• CanceltheAVmutebypressingtheAVMUTEbutton.
• Checkthatthelenscapisremoved.
• Itmaytakeabout1minuteforthelamptolightup.
• Thelampfailstolightuponrareoccasions.Insuchacase,waitforafewminutes
and then try again.
• Iftheprojectorwasturnedoffbeforethelampwascooleddownsufcientlylasttime,
the fan may start rotating and the POWER button may not work after the power cord
is plugged. Press the POWER button to turn back on the POWER indicator.
• Checkthattheintakeventisclean.
• Checkthatthelampcoverisclosed.(Seepage58or59.)
• Checkthatthecablesconnectedtotheexternaldevicesarenotbroken.
• Whenanextensioncableisbeingused,replaceitwiththesuppliedcableforcheck.
When images are displayed correctly, add an RGB signal amplifier to the extension
cable.
Power turns off. • Thisproblemmayoccurwhentheintakeventand/orexhaustventsareblocked.(In
such a case, the STATUS indicator brinks orange.)
Remove the objects blocking the intake vent and/or exhaust vents and then carry
out the following procedure.
1. Wait for the intake fan and/or exhaust fan to stop. (Wait until the STATUS indicator
goes out.)
2. Unplug the power cord from the wall outlet.
3. Wait about 10 minutes.
4. Plug the power cord into the wall outlet.
5. Press the POWER button.
• WhentheSTATUSindicatorissteadyred,itisindicatingthatthelampshouldbe
replaced. Replace the lamp in this case.
• CheckthatAutoPowerOffhasbeensettoOff.
• Ifthelamphasdeteriorated,itmaygooutafterawhileitilluminates.
60


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi WD390U-EST at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi WD390U-EST in the language / languages: English as an attachment in your email.

The manual is 10,54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Mitsubishi WD390U-EST

Mitsubishi WD390U-EST Additional guide - English - 30 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info