549869
59
Zoom out
Zoom in
Previous page
1/69
Next page
EN-59
Lamp replacement (continued)
3. Fold the three taping portions (g) of the lamp
replacement attachment along the folding line as
shown in the figure.
(g)
4. Fit the lamp replacement attachment to the edge
of the lamp cover attachment part on the projector
(h) and fix the three taping portions (g) with the tape
included in the lamp replacement attachment.
(g)
(h)
5.
Pull out the lamp unit (f) in the bag by the handle (e).
(f)
(e)
6. Remove the tape fixing the lamp replacement
attachment, and remove the lamp replacement
attachment with the lamp unit remaining in the bag.
Caution:
• Pullthelampunitoutoftheprojectorslowly.
If it is pulled out quickly, the lamp may break,
scattering glass fragments.
• Donotspillliquidontheremovedlampunitor
do not place it near any flammable object or
where children can reach to prevent injuries or
fire.
7. Insert the new lamp unit, and secure it with two
screws firmly.
8. Secure the lamp cover with screw (b) back again,
and mount the cover (a).
Caution:
•
Make sure that the lamp cover is secured firmly.
Otherwise, the POWER indicator flashes red and
green, disallowing the projector to be powered on.
Reset of the lamp operation time
Plug in the power cord, and reset the lamp operation
time by keep pressing the , , and POWER buttons
on the control panel at the same time.
Important:
• Unlessthesethreebuttonsarepressedatthesame
time, the lamp operation time isn’t reset.
• MakesurethattheSTATUSindicatorislittwiceand
the lamp operation time is reset successfully.
• Theprojectordoesn’tturnonifthelampcoverisn’t
attached securely.
• Besuretoresetthelampoperationtimewhenever
you replace the lamp.
• Donotresetthelampoperationtimeunlessyou
replace the lamp.
Caution:
• Thelampisfragile.Ifitisbroken,becarefulnotto
cut yourself with glass fragments.
• Contactyourdealerforanewlamp.
Interval of lamp replacement
The recommended interval of lamp replacement is
about 6000 hours
*1*2
of consecutive use. Such interval
differs depending on the operating environment and
may be shorter than 6000 hours
*1*2
.
Decrease in luminescence and/or color brightness
indicates that the lamp needs to be replaced. When
the lamp operation time exceeds 4500 hours
*1
, the
indicator will blink alternately between green and
red (while the lamp is lit; when the lamp is not lit, the
indicator will be lit red only) and the lamp replacement
message will appear on the screen for one minute
everytime the lamp is turned on. When the lamp has
been used for about 5700 hours
*1
, the replacement
message (Lamp Replacement) will appear on the
screen for one minute every 30 hours
*1
thereafter.
When the lamp operation time exceeds 6000
hours
*1*2
, the projector automatically shuts off and
can’t be used until the lamp is replaced and the
lamp operation time is reset.
*1: Duration when Lamp Mode of the Installation menu is set
to Low. When it is set to Standard, this duration will be
shorted.
*2: When Lamp Mode is set to Standard, this duration will be
shorted to 3000 hours.
Important:
• Donotopenthelampcoverwhentheprojectoris
set at a ceiling or a high place. Lamp fragments
may fall from the inside if the lamp were broken.
Please contact your dealer when you need to
replace the lamp with a new one.
Caution:
This projector uses a lamp that
contains mercury. Disposal of the lamp
or the projector with the lamp may
be regulated due to environmental
considerations. For disposal or
recycling information, please contact
your local authorities or the Electronic
Industries Alliance: www.eiae.org. (For
the U.S. only.)
59


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi WD390U-EST at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi WD390U-EST in the language / languages: English as an attachment in your email.

The manual is 10,54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Mitsubishi WD390U-EST

Mitsubishi WD390U-EST Additional guide - English - 30 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info