475327

Mitsubishi WD-73C8 Manual

61
Zoom out
Zoom in
Previous page
1/94
Next page
6. NetCommand IR Control (736 and 835 Series TVs) 61
Setting Up NetCommand Control of an A/V Receiver, continued
Audio Switching Setup 2: Automatic A/V Receiver
Switching to a Surround Sound Device
Use this setup to send digital surround sound directly
from a device to an A/V receiver.
Under
1.
Learn, highlight Input2.
In this example, the IR code for the A/V receiver’s
DVD Audio
input will be “learned” as Input2.
Press
2.
ENTER
on the TV’s remote control.
57
BVEJPWJEFP
*ODPNJOH
$PBYJBM
$BCMF
"73FDFJWFS
%7%BVEJP
JOQVU
%7%1MBZFSXJUI
%JHJUBM4VSSPVOE4PVOE
WJEFP
WJEFP
EJHJUBMTVSSPVOETPVOE
EJHJUBMTVSSPVOETPVOE
WJEFP
BOBMPHBVEJP
%7%1MBZFS
XJUI
%JHJUBM
4VSSPVOE
4PVOE
Setup 2: A/V receiver audio from a device providing
surround sound directly to the A/V receiver
Completed NetCommand setup described for
controlling A/V receiver switching to an A/V receiver
input “learned” as Input2.
While the text
3.
Input2 is flashing, press and hold the
DVD INPUT
key on the A/V receiver’s remote control.
When a check appears next to
4.
Input2, release the
DVD INPUT
key.
If the text stops flashing before the check mark •
appears, repeat this step.
To erase the IR code just “learned,” press •
CANCEL
while the name is highlighted.
Press
5.
once to move the highlight to the Assign
Input2 column.
Use
6.
to highlight DVD in the list of devices
recognized by the TV. The triangular marker always
shows the assigned sound source.
Press
7.
EXIT
if finished or continue for additional TV
sources.
A/V Receiver Control: Automatic Audio
and Video Switching via HDMI
If your A/V receiver has an HDMI output, you can use
this procedure to set up control of the A/V receiver’s
audio and video switching. The HDMI connection
allows you to route video signals from multiple devices
over a single cable to the TV. See the diagram on the
next page. The connected devices can be analog,
digital, or a mixture or the two.
More About Using an HDMI Connection
Audio from devices connected directly to the TV •
can be heard from the TV speakers only. This is
because audio signals are sent on the HDMI cable
in one direction only—through the A/V receiver to
the TV speakers.
To send audio to the A/V receiver from a device
connected directly to the TV, use one of the optional
audio connections shown in the diagram. For
example, use an optional audio connection if you
wish to use the A/V receiver speakers to hear audio
from:
The -
ANT 1
or
ANT 2
inputs
A device connected to the convenience input -
(
INPUT 4
), such as a game or camcorder.
In some circumstances, audio from a device con-•
nected to the A/V receiver may not be passed over
the HDMI cable to the TV speakers. You must use
the A/V receiver speakers to hear audio in these
cases.
Before You Begin
To complete these steps you will need:
The remote controls for both the TV and the •
A/V receiver.
The IR emitter cable supplied with the TV.•
An HDMI-to-HDMI cable to connect the A/V •
receiver to the TV and cables necessary to
connect devices to the A/V receiver.
Connect your audio/video devices to the A/V
1.
receiver. Note the name of the device connected
to each A/V receiver input. This information will be
needed later to set up NetCommand’s automatic
input switching.
Connect the A/V receiver to the TV with an HDMI-
2.
to-HDMI cable.
Connect the IR emitter cable to the TV and position
3.
the IR emitter where it can send signals to the A/V
receiver. See “IR Emitter Placement,” page 53.
… 61 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi WD-73C8 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi WD-73C8 in the language / languages: English as an attachment in your email.

The manual is 4,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info