475327
59
Zoom out
Zoom in
Previous page
1/94
Next page
6. NetCommand IR Control (736 and 835 Series TVs) 59
Setting Up NetCommand Control of an A/V Receiver, continued
Perform one of these setups to enable the A/V receiver
to switch automatically to the correct audio input when
you select a device in the TV’s Input Selection menu.
To set up control of an A/V receiver you need:
The remote controls for both the TV and the A/V •
receiver.
The IR emitter cable supplied with the TV.•
Connecting cables•
Two different setups are described here. Review the
descriptions to find the setup needed for your equipment.
Audio Available from TV only•
Audio from
ANT 1
and
ANT 2
must be sent to
the A/V receiver from the TV’s DIGITAL AUDIO
OUTPUT or analog
AVR AUDIO OUTPUT
.
Use Setup 1 to make the A/V receiver switch to its
designated TV audio input when viewing these sources.
Analog Stereo Audio•
Audio from sources with only analog stereo output
(such as a VCR) can be sent either directly to the
A/V receiver or through to the TV and then on to the
A/V receiver.
Mitsubishi recommends you send audio through
the TV as shown in the example. Setup 1 causes
the A/V receiver to switch to its input designated for
TV audio.
If you have a digital A/V receiver, the TV makes the
audio available by converting analog audio to a
digital output.
HDMI Digital Stereo Audio•
Digital stereo audio from an HDMI connection
is available both in digital format (from the TV’s
DIGITAL AUDIO OUTPUT jack) and in analog
format (from the TV’s
AVR AUDIO OUTPUT
jack).
Audio Switching Setup 1: Audio to the A/V receiver
from the TV’s digital or analog audio output
Note: This setup is required to hear digital sur-
round sound
A device can send digital surround sound such as
Dolby Digital or DTS directly to the A/V receiver,
bypassing the TV entirely. The device might be a DVD
player, cable box, or satellite receiver, and could have
HDMI output. A DVD player is used in this example.
Your setup may include additional devices with digital
surround sound connected directly to the A/V receiver.
These devices might be a DVD player plus a cable box
or satellite receiver.
57
BVEJPWJEFP
*ODPNJOH
$PBYJBM
$BCMF
"73FDFJWFS
%7%BVEJP
JOQVU
%7%1MBZFSXJUI
%JHJUBM4VSSPVOE4PVOE
WJEFP
WJEFP
EJHJUBMTVSSPVOETPVOE
EJHJUBMTVSSPVOETPVOE
WJEFP
BOBMPHBVEJP
%7%1MBZFS
XJUI
%JHJUBM
4VSSPVOE
4PVOE
Audio Switching Setup 2: Audio from a device
providing surround sound is sent directly to the A/V
receiver.
TV
audio + video
Incoming Coaxial Cable
to ANT 1/ANT 2
A/V Receiver
DVD audio
input
TV audio input
TV audio
out
audio output from
TV (digital or analog)
video
analog audio
VCR with
Analog Audio Output
Audio Switching Setup 1: Automatic A/V Receiver
Switching to TV Audio Input
Audio Switching Setup 2: Automatic A/V Receiver
Switching to a device sending audio directly to the A/V
receiver. You must use setup 2 to hear digital sur-
round sound from the source device.
Note: Automatic audio and video switching over an
HDMI cable is covered on page 61.
A/V Receiver Control: Automatic Audio Switching
Audio Switching Setup 1: Audio
from TV’s Audio Output
Audio Switching Setup 2: Audio from Source Device
59


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi WD-73C8 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi WD-73C8 in the language / languages: English as an attachment in your email.

The manual is 4,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info