475257
67
Zoom out
Zoom in
Previous page
1/110
Next page
5. NetCommand IR Control (838 Series) 67
For assistance call 1(800) 332-2119
Operating NetCommand-Controlled
Devices
Controlling Most Device Types
As an example of NetCommand control, if you are
watching your cable box and you wish to tune to the
next channel higher, press
CHANNEL UP
. NetCommand
then sends the “learned” channel-up control signal to
the cable box.
1.
Perform NetCommand setup for the device as
described in this chapter.
2.
When you wish to use the device, press
INPUT
.
3.
Highlight the icon for the device.
4.
Press
ENTER
to switch the TV to the device.
Note: if you have set up automatic input switching for
the A/V receiver, the A/V receiver will automati-
cally switch to the correct input for the device.
5.
To operate the device using the TV’s remote
control, press the
TV
key to put the remote control
into TV mode.
6.
Point the remote control at the TV (not the device)
and press the key for the desired function.
7.
Press the
TOOLS
key to access additional key func-
tions you may have “learned” for the device.
After performing initial setup, you can add or remove
individual keys under NetCommand control.
1.
Switch the TV to the device. Press
INPUT
, highlight
the device’s icon, and press
ENTER
.
2.
Open the Inputs menu and highlight the Learn icon.
3.
When the Learn screen displays:
• To add keys: Continue as described earlier
under “Initial NetCommand Setup” on the
opposite page.
• To delete keys: Highlight the name of the key
you wish to delete and press
CANCEL
on the
TV‘s remote control. Clears the check mark.
NetCommand Setup, continued
Adding or Removing Device Keys from
NetCommand Control
Special Operation Methods
Key Name in
Learning Screen
Special Operation Description and Setup How to Use
Power On Manual Power On/Off
Use for devices that have only one
POWER
key.
1. Press
INPUT
.
2. Highlight the icon for the device to be
powered on or off.
3. With the Input Selection menu still dis-
played, press
POWER
to send the power
signal; you may need to press
POWER
twice.
Note: If you press
POWER
without the Input Se-
lection menu displayed, the TV will turn
off.
4. Press
ENTER
to switch the TV to the device.
Power On
Power Off
Automatic Power On/Off
This feature is only for devices that have separate
POWER ON
and
POWER OFF
keys on their original
remote controls. If your device does not have a
separate
POWER OFF
key, do not use the Power
Off learning position; use only the Manual Power
ON/OFF method described above.
In the NetCommand Learn screen:
a. Learn” the Power On command in the
Power On learning position.
b. “Learn” the Power Off command in the
Power Off learning position.
• To Power On the Device
1. Press
INPUT
.
2. Highlight the icon for the device to be
powered on or off.
3. Press
ENTER
to switch the TV to the
device and NetCommand will send the
Power On command to the device.
• To Power Off the Device
When you turn the TV off, the TV sends all
learned Power Off commands to all devices.
67


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi WD-73838 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi WD-73838 in the language / languages: English as an attachment in your email.

The manual is 7,62 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info