475257

Mitsubishi WD-73838 Manual

66
Zoom out
Zoom in
Previous page
1/110
Next page
66 5. NetCommand IR Control (838 Series)
For assistance call 1(800) 332-2119
Initial NetCommand Setup
To perform this procedure, you need:
• The remote controls for both the TV and the
device you want to control.
• An IR emitter cable available from Mitsubishi
.
Note: To set up an A/V receiver, see “Setting Up A/V
Receiver Control,” page 71.
1.
Connect and position the IR emitters for the
devices you wish to control. See “IR Emitters” on
the previous page.
2.
Set the TV’s remote control to
TV
mode and power
on the TV.
NetCommand Setup
NetCommand and Device-Specific Keys
Device-specific keys are those which have no
equivalent on the TV’s remote control. Use any of
these methods to set up NetCommand control for
these keys.
• TOOLS Menu. In some cases, the TV will, by
default, assign a key to the TOOLS menu. See
the table below.
Examples of Default NetCommand
Assignments in the TOOLS Menu
Cable Box, Sat-
ellite Receiver
3
MENU
9
ON DEMAND
DVD, DVR,
Blu-ray
3
SETUP
6
TOP MENU
9
ANGLE
VCR 3
MENU
6
INPUT
A/V Receiver 3
MENU
6
SURROUND
NetCommand’s default setup assigns some
device-specific keys to the TOOLS menu when
“learned.” These key functions are accessible only
with the
TOOLS
key.
•
F
Keys. There are four
F
keys,
F1
through
F4
,
which you can assign to any function on the
device’s remote control. For a cable box,
“learn” the
F
keys as the
A, B, C, D
keys.
• Arbitrary Key Assignment. You can assign a
device key arbitrarily to any “unlearned” key
on the TV’s remote control. Make a note of the
key name and function for later reference.
3.
Switch the TV to the desired input to control. Press
INPUT
, highlight the input icon, and press
ENTER
.
4.
Open the NetCommand Inputs > Learn menu.
5.
The first function highlighted in the Learn screen
is always Power On. Aim the TV’s remote control
at the TV and press
ENTER
to begin learning for that
function.
6.
When the
Power On
text starts flashing, aim the
device’s
remote control at the TV and hold the
POWER
key until a check mark appears next to Power On.
• If the text stops flashing before the check mark
appears, repeat the previous step.
• To remove the key from NetCommand control,
press the
CANCEL
key while the key name is
highlighted.
• To verify the device’s response to the IR code,
press
ENTER
to send out the code.
Inputs > Learn screen. Key names marked with a check
have been “learned.”
Some device-specific keys, such as
MENU
, are available
only from the TOOLS menu after “learning.”
7.
Use navigation keys on the TV’s remote control to
highlight other keys on the list. Repeat steps 5 and
6 for each additional function you wish to control
through NetCommand.
8.
If the device has a separate
POWER OFF
key, use
navigation keys on the TV’s remote to highlight
Power Off.
Repeat the earlier steps to “learn” the
POWER OFF
key.
If the device has no
POWER OFF
key, skip this step.
9.
Press
EXIT
to finish NetCommand “learning” for the
current device.
… 66 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi WD-73838 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi WD-73838 in the language / languages: English as an attachment in your email.

The manual is 7,62 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info