475319

Mitsubishi WD-62628 Manual

45
Zoom out
Zoom in
Previous page
1/124
Next page
Chapter 3. NetCommand Setup and Editing 45
Edit NetCommand®: Add an A/V Receiver
A/V Receiver Screen
Figure 8
If your A/V Receiver manufacturer was not listed, and you
selected “None” during the initial NetCommand setup,
you may add the A/V Receiver and have NetCommand
learn its remote control’s functions. Either select Edit
from the Finish screen or, if you have finished the initial
setup, go to the Main menu, select NetCommand, then
press ENTER. The Edit NetCommand screen will display.
Select Add.
Figure 8. A/V receiver screen
Choose ONE of these options:
• Selectarecognizedmanufacturer.Themodel
number optimized for NetCommand will display at
the bottom of the screen. If a number follows the
manufacturer’s name, (example: Mitsubishi 1), this
indicates additional models are optimized for that
manufacturer. For many device types, non-listed
models will operate in the same way as the listed
models and you can still use the pre-loaded setting.
After selecting Next>, the screens that follow are:
the Name Screen (Figure 12), Audio Output to AVR
screen (Figure 13), ending with the Finish screen
(Figure 14).
• Select“Other,”thenhighlight“Learn” and press
ENTER. This will allow you to have NetCommand
learn the remote control signals of this new device.
After selecting “Learn” and pressing ENTER, the
screens that follow are: the A/V receiver Inputs
screen (Figure 9), A/V Receiver Input Learn screen
(Figure 10), A/V Receiver Learn screen (Figure 11),
Name screen (Figure 12), Audio Output to AVR screen
(Figure 13), ending with the Finish screen (Figure 14).
• Select“Other,”skipLearnandselectNext>. This
will allow the device to appear and will allow
NetCommand to switch inputs to use this device.
However, NetCommand will not be able to control
this device. Later you may use the “Change” option
in the NetCommand menu to learn the remote control
signals.
After selecting Next>, the screens that follow are: the
A/V Receiver Input screen (Figure 9), Name screen
(Figure 12), Audio Output to AVR screen (Figure 13),
ending with the Finish screen (Figure 14).
A/V Receiver Inputs
Figure 9
If you select “Other” as the manufacturer and then
“Learn,” you will see the A/V Receiver Input screen. After
selecting the number of inputs, this screen will not appear
again.
Depending on your A/V Receiver’s capability, you may
connect up to seven A/V inputs. Select the number of
inputs by pressing ADJUST or .
If the number of connected inputs changes, you will need
to delete the A/V receiver through Edit NetCommand and
add it again, as described above.
Figure 9. A/V receiver Input screen
… 45 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi WD-62628 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi WD-62628 in the language / languages: English as an attachment in your email.

The manual is 7,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info