475319

Mitsubishi WD-62628 Manual

43
Zoom out
Zoom in
Previous page
1/124
Next page
Chapter 3. NetCommand Setup and Editing 43
NetCommand must be set up and the IR
emitters properly placed for your cable box
and VCR so the TV Guide On Screen system
can control these devices.
IMPORTANT
NetCommand
®
Initial Setup, continued
Device Setup Screen
Figure 4
If the devices connected to the TV are already in
NetCommand memory, you can quickly select them
at this screen. Press ADJUST or to move to each
device type. Press ADJUST or to select the
manufacturer. Select “Other” if the manufacturer is not
listed. Later, you can use the Change setting in the Edit
NetCommand menu to learn the remote control signals
for this device. Select “None” for device types that are
not connected.
For the A/V Receiver, if the manufacturer is not listed, you
cannot select “Other”. Instead, select “None”. Later, you
can use the “Add” feature in the NetCommand menu to
have the TV add and learn the remote control signals for
this device.
If you have a camcorder connected, check the
Camcorder box. NetCommand will not be able to
control it, but will reserve the front input to use with
the camcorder. Check the PC box if you have a PC
connected. After completing your choices, select Next>
and press ENTER.
Figure 4. Device Setup screen
Note: If you selected “Other” for any of the device
names, you can direct the TV to “Learn” the connected
device by following the Edit NetCommand instructions.
For many device types, non-listed models will operate in
the same way as the listed models and you can still use
the pre-loaded setting.
TV Guide On Screen® System Setup
Figure 5
The TV Guide On Screen option allows you to select
whether you want to enable the TV Guide On Screen
system and, if so, which devices to include. To receive
the correct program listings for your area, you will need to
enter your five-digit ZIP code.
You can select one over-the-air source and one cable
source for TV Guide On Screen. If, however, you have
multiple cable sources, the channel-number assignments
may not match up correctly. See the table below for the
preferred connection combinations.
If One Source Is:
The Other Source Can Be:
Ant-1 Air Ant-2 Air
Cable Box
Cable Card N/A
Ant-1 Channels via Cable N/A
Ant-2 Channels via Cable N/A
For detailed information on using the TV Guide On
Screen system, please see the separate TV Guide On
Screen Interactive Program Guide User’s Manual.
Figure 5. TV Guide On Screen
Note:
• InputstoTVGuideOnScreencaninclude:
- Only one over-the-air source
- Only one cable source
• AnantennainputisrequiredfordownloadingTV
Guide On Screen schedules. If your cable box is
connected using HDMI or IEEE-1394, you must also
connect an antenna input.
• IfyourcableboxisconnectedtoaComponentinput,
be sure the box is set to send analog channels as
480i. If this is not possible, add an antenna input.
… 43 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi WD-62628 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi WD-62628 in the language / languages: English as an attachment in your email.

The manual is 7,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info