475335

Mitsubishi WD-57831 Manual

32
Zoom out
Zoom in
Previous page
1/126
Next page
32 Chapter 2. TV Connections
Q. My VCR (or other device) does not have two sets of stereo audio outputs. How can I connect this device’s
audio to both the TV and the A/V Receiver?
A. YouneedtoconnectthedevicetotheTVandthenmakechangestotheA/Vreceiversetup.
1. ConnecttheVCR’saudioandvideototheTV;connectthesinglesetofstereoaudiooutputstotheTVonly.
2. Performtheprocedureforsettingupadeviceconnection.Seechapter3,“TVSetup,”andthesectionentitled
“WhenYouFirstConnectaDevice.”NetCommandIRLearningisoptional.
2. Press
INPUT
todisplaytheInputSelectionmenu,highlighttheVCR’sicon,andpress
ENTER
toselecttheVCR.
3. Press
MENU
toopentheMainmenu,highlighttheNetCommandicon,andpress
ENTER
.
4. UnderAV RECEIVER SETUP,confirmthatthetextboxdisplaysNone.
5. Press
EXIT
.
Afterperformingthesesteps,theTVwillautomaticallypasstheaudiosignaltotheA/Vreceiver.
Q. I have both the TV stereo audio output and TV digital audio output connected to the same input designa-
tions on my A/V Receiver. How do I switch between analog audio and digital audio?
A. Inmostsetups,analogaudioisalsooutputasdigitalaudio,sonoswitchingisrequired,andthereisnoneedto
connecttheanalogoutput.Insomecircumstances,however,youmayalsoneedanalogaudiofromtheTV.For
example,MP3audioisonlyoutputinanalogformat,soyoumustconnecttheTV’sanalogAUDIOOUTPUTtothe
A/VReceiverifyouwanttohearMP3audiothroughtheA/Vreceiver.RefertoyourA/VReceiveruser’sguideto
findouthowanalog/digitalaudioswitchingworks.
Q. The front panel of my A/V Receiver is too tall or too convex for the IR emitter signal to reach the remote
control sensor of the A/V Receiver. What can I do?
A. Thereareseveralpossiblesolutions.
• MounttheIREmitteronthetop,frontedgeoftheA/VReceiverovertheremotecontrolsensor.Usetapeto
secureitinplace.
• MounttheIREmitterontheundersideoftheshelfabovetheA/VReceiver(iftheA/VReceiverisinacabinet).
Usedoublesidedtapetosecureitinplace.
• Somesmallstick-onemittersfromothermanufacturersmaybecompatiblewiththisTV’sIREmitterjacks.
ThesemaybeusedinsteadofthesuppliedIREmitters.
Q. I occasionally need to see the menu from my A/V Receiver. How can I connect it to the TV for this purpose?
A. ConnecttheA/VReceiver’svideooutputtoanunusedinputontheTVandthenusetheA/Vreceiver’sremote
controltodisplaythemenu.
1. ConnectthevideooutputoftheA/VReceivertoanunusedinputontheTV;Input3onthefrontpanelisthe
mostconvenient.TheAutoInputSensingscreenwilldisplayswhentheTVdetectsthenewconnection,
2. PressEXITtoclosethescreenwithoutnamingtheinput.
3. Select
INPUT 3
(orotherinputyouused)fromtheInputSelectionmenu:press
INPUT
,highlighttheInput3icon,
andpress
ENTER
.
4. Pressthe
MENU
keyontheA/Vreceiver’sremotecontroltoopentheA/Vreceiver’smenu.
5. Whenfinished,disconnecttheA/Vreceiver’svideoinputfromtheTV.
Q. I have a high definition receiver I would like to connect and it also has an S-video output I would like to be
able use as well. Is there any way to connect this receiver both ways?
A. Yes,thisitemwillappeartwiceintheInputSelectionMenu.Justaddthisunitonceusingthe
COMPONENT
orHDMIinputandonceusingoneofthe
S-VIDEO
inputs.Mitsubishisuggeststhatyouconnectstereoaudio
outputswiththeS-videoinputonly.
Helpful Hints for NetCommand Connections
… 32 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi WD-57831 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi WD-57831 in the language / languages: English as an attachment in your email.

The manual is 8,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info