475321
33
Zoom out
Zoom in
Previous page
1/118
Next page
Chapter 2. Connecting 33
When Connecting IEEE 1394 Devices
Do not loop the last device in the chain back
to the TV. When the device chain is looped,
the TV may not be able to work with the other
devices.
Place devices that have only a mechanical (two-
position) power switch at the end of the chain
or leave the power switch in the On position.
When turned Off, IEEE 1394 signals may not
be able to pass through the device to other
devices.
Place devices with the slowest communication
speed at the end of the chain. Sometimes
the communication speed will be marked
near the IEEE 1394 connector with an “S”
number. The higher the number, the faster
the communication speed. This TV has a
communication speed of S400. Devices with
slow communication speed can interfere
with IEEE 1394 signals from faster devices.
When using NetCommand to set up a digital
recording between a faster and slower device,
the slower device should be the source and the
faster device should be the recorder.
Do not use an IEEE 1394 cable longer than 15
feet between each device.
This TV is an IEEE 1394a device. It can be used
with a 1394b system when an IEEE 1394a to
1394b convertor is used. 1394b systems enable
longer distance and multi-room applications.
Connecting Compatible IEEE 1394 Devices
Compatible IEEE 1394 Devices
It is possible to connect devices to the TV that have IEEE
1394 connectors but are not compatible with the TV or with
the NetCommand
®
control system. Areas of compatibility
to consider are:
1. Digital Video Signals
The TV is able to decode MPEG2 video. Other types
of digital video, such as DV video provided by some
camcorders, must be decoded by the source device
and sent to the TV as analog video, or S-video. If the
camcorder uses a compatible digital control system,
the IEEE 1394 cable can still provide control for the
camcorder while the TV is viewing the analog video or
S-Video signals.
2. Digital Audio Signals
When received with video signals, the TV is able to
decode Dolby Digital signals and MPEG audio signals.
Other types of digital audio as provided by some digital
recording devices, such as MP3 audio and DTS audio,
cannot be decoded by the TV when received over IEEE
1394
The TV may not be able to pass incompatible digital
audio signals on the coaxial digital audio output,
however these signals may pass on the IEEE 1394 cable
to other devices.
3. Digital Control Signal
The TV is able to act as the control center for IEEE 1394
audio/video devices, such as VCRs, A/V Discs, tuners,
cable boxes and amplifiers that are compatible with the
following IEEE 1394 control standards.
EIA-775 is designed for tuning devices such as cable
boxes allowing the device to send simple graphics.
However, this standard does not allow the TV to
control the cable box by IEEE 1394.
AV/C (Audio Video Control) is designed to provide
basic controls such as play, stop, channel selection
and volume, as appropriate for the device.
Some devices may be a combination of two or more
types of devices. For example, there may be a
recording device that is also a tuning device. Each
portion of the device is called a sub-unit. When you
select a device on the Device Selection menu that
has sub-units, a pop-up menu will appear so you can
select which sub-unit section you wish to use.
33


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi WD-52627 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi WD-52627 in the language / languages: English as an attachment in your email.

The manual is 8,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info