475321
32
Zoom out
Zoom in
Previous page
1/118
Next page
32 Chapter 2. Connecting
Connecting the IR Emitter NetCommand
®
If a single emitter end can be placed in a
position that will operate more than one device,
do not use a separate emitter end for the
additional device. A single device receiving
remote control signals from too many emitters
or remote controls may not respond at all.
IMPORTANT
IR Emitter NetCommand®
Figure 15
An IR emitter cable is included with the TV.
The emitters connected to these jacks are used by the
NetCommand system to control other devices such as
VCRs, DVD players, Cable boxes and Satellite receivers.
1. Connect the plug end of the supplied IR Emitter
Cable to either one of the IR Output NetCommand
jacks on the TV back panel.
2. Run the cable for each of the emitter ends under,
along side or over the top of each device to be
controlled to the area of the front where the remote
control sensor is located.
3. Place the emitter end in front of the remote control
sensor of the device to be controlled. The emitter
bulb should face the remote control sensor. This
bulb emits infrared light in a cone shaped pattern.
The bulb needs to be placed far enough from the
remote control sensor to allow the cone pattern to
include the sensor.
The remote control sensor is usually behind the
plastic window of the front display panel. It is
sometimes visible when you look through the
display plastic using a flashlight and is normally a
round or square cutout behind the plastic. If you
cannot see the sensor and the device’s Owners
Guide does not specify the location, you can find it
by using the device’s remote control.
a. Hold the remote about 1/2 inch from the front of
the device. Starting from one end of the display
window plastic, press the POWER button.
b. If the device does not respond, move the remote
control 1 inch toward the center and try again.
c. Repeat this until the device responds.
d. Note this location and then start over from the
other end of the display window plastic, repeating
until the device responds again.
The remote control sensor will be somewhere
between these two positions. This is usually
enough accuracy for the placement of the IR
emitters.
With some devices, the emitter works better facing
downward from the top of the device. Some
experimentation may be needed.
The emitter end being used can be secured in place
using double stick tape.
If you are not going to
be using all emitter ends, place
the unused ends behind the devices so that they
cannot send signals to the remote control sensors.
% *( * 5" -
46 330 6/%
4
$)





57CBDL
QBOFMEFUBJM
0UIFS"7EFWJDF
"7SFDFJWFS
Figure 15. Connecting IR Emitter NetCommand
32


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi WD-52627 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi WD-52627 in the language / languages: English as an attachment in your email.

The manual is 8,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info