When the problems below occur after the lamp is replaced, check the following.
Maintenance
Warning:
Do not use flammable solvents (benzene, thinner, etc.) and flammable aerosols when cleaning the projector body and lens. Flammable substances
may ignite causing fire or breakdown while the lamp is illuminating.
Caution:
Be sure to turn off the lamp and unplug the power cord from the wall outlet before you perform any maintenance on the projector.
Cleaning of the projector and the ventilation slots
Use a soft cloth to clean the projector and the ventilation grilles. When the grilles become dirty, wipe them with a soft cloth dampened with diluted
mild detergent, and then wipe them with a dry cloth.
To protect the surface of the projector from fading or deteriorating:
•Do not spray insecticide on or inside the projector.
•Do not use benzine or thinner to clean it.
•Do not let rubber or plastic materials contact with projector.
Cleaning of the lens
Use a standard lens-cleaning brush or a piece of lens tissue dampened with lens cleaning fluid. The lens surface is fragile. Use only recommended,
nonabrasive lens-cleaning materials. Do not touch the lens with your fingers.
ProblemCause and solution
Hot air is emitted from the air outlet grilles.•This air comes out as a result of cooling the inside of the projector. This isn’t a product malfunction.
No audio is output. •Check that the volume isn’t set to low.
Sound cannot be heard from the external audio out-
put (* Only applicable to the models which have the
external audio output.)
•Check whether or not the volume is turned down.
The menu can’t be used.
•The microcomputers inside the projector may be wrongly operating because of noise.
JPress the POWER button to turn off the lamp and unplug the power cord from the wall outlet. Wait about
10 minutes, plug the power cord in, and try again.
The remote control doesn’t function easily or at all.
•Check that the battery is loaded in the remote control or the battery isn’t weak. (See page 8.)
•Check that the remote control sensor isn’t exposed to direct sunlight or fluorescent light. (See page 8.)
•Use the remote control within its operation range. (See page 8.)
•Use the remote control at least 10 cm away from the projector.
The buttons on the control panel (except for the
POWER button) don’t function.
•The password function is working.
JCancel the password lock. (See page 21.)
Abnormal sound is heard.
•Because the color wheel spins at a high speed, metallic sounds may be heard in rare occasions. Such symp-
tom is not a malfunction.
•95% Lamp life exceed
JReplace the lamp and reset the lamp hour.
Steady green
Blinking red
ProblemCause and solution
The power isn’t turned on.
•Attach the lamp cover on the bottom correctly.
•Reset the lamp operation time. (See page 22.)
The STATUS indicator blinks. •Reset the lamp operation time. (See page 22.)
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Mitsubishi SD206U at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Mitsubishi SD206U in the language / languages: English as an attachment in your email.
The manual is 1,05 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
