604759
34
Zoom out
Zoom in
Previous page
1/40
Next page
32
8.0 [N] Other adjustments
Menu 8.1.0 [N] Display settings
Settings concerning language and menu type are set in the sub-
menus to this menu.
Menu 8.1.1 [N] Menu type
The menu type is chosen here.
[N]
 
Normal, covers the normal users needs.
[U]
 
Extended, shows all menus except the service menus.
[S]
 
Service, shows all menus, returns to normal menu level
30 minutes after the last button was pressed.
NOTE
Incorrect settings in the service menus can damage the
property and/or heat pump.
Setting range: N, U, S
Menu 8.1.2 [N] Language
Language settings are made here.
Menu 8.1.3 [U] Display contrast
The display’s contrast is set here.
Setting range: 0 – 31
Menu 8.1.4 [U] Light intensity
The light intensity in idle mode is set here. Idle mode starts 30
minutes after the last button was pushed.
Setting range: 0=off, 1=low, 2=average.
Menu 8.1.5 [N] Return
Return to menu 8.1.0.
Menu 8.2.0 [N] Op. mode settings
Settings regarding auto mode can be made in the sub-menus to
this menu.
Menu 8.2.1 [N] Allow add. heat
You can choose at which operating mode the electric heater is
to be permitted to produce hot water and heat when needed.
Setting range: Off, Heating, Heating + Cooling, Cooling
Default values: Heating
Menu 8.2.2 [N] Add. heat mode
Selected if electric heater only is to be used to produce hot
water and heat.
Setting range: Off, On
Control
Menu 8.2.3 [U] Stop temp. heating
The average outdoor air temperature at which the heat pump (in
auto mode) is to stop heat production.
When the average outdoor air temperature falls below Stop
temp. heating – Hysteresis (menu 8.2.5) heating starts again.
Setting range: 1 – 43 °C
Menu 8.2.4 [U] Start temp. cooling
The average outdoor air temperature at which the heat pump (in
autoC mode) is to start cooling.
When the average outdoor temperature exceed it, cooling
starts.
When the average outdoor air temperature falls below Start
temp. cooling – Hysteresis (menu 8.2.5) cooling stops.
Setting range: 10 – 43* °C
* Operable temperature range is 15 – 43 °C.
Menu 8.2.5 [U] Hysteresis
See menu 8.2.3 and menu 8.2.4. Also affects control with room
sensor.
Setting range: 1.0 – 10.0
Menu 8.2.6 [N] Return
Return to menu 8.2.0.
Menu 8.3.0 [U] Current limiter
Settings and readings regarding the load monitor are set in the
sub-menus to this menu.
Menu 8.3.1 [U] Fuse size
The setting selected on the PCB (AA22) switch (R24) is shown
here.
Menu 8.3.2 [U] Max. electric power
The setting selected on the PCB (AA22) switch (R25) is shown
here.
Menu 8.3.3 [U] Current phase 1
Measured current from phase 1 shown here. If the value falls
below 2.8 A “low” is displayed.
Menu 8.3.4 [U] Current phase 2
Measured current from phase 2 shown here. If the value falls
below 2.8 A “low” is displayed.
Menu 8.3.5 [U] Current phase 3
Measured current from phase 3 shown here. If the value falls
below 2.8 A “low” is displayed.
Menu 8.3.6 [U] Transform. ratio EBV
The transfer value must be defined depending on the current
transformers used for the PCB.
Setting range: 100 – 1250
34


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi HMS140VA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi HMS140VA in the language / languages: English as an attachment in your email.

The manual is 2,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info