30505

Mitsubishi HD5000 Manual

21
Zoom out
Zoom in
Previous page
1/24
Next page
21
Problem Possible Solution
• The IEEE  plug does not fit into HDTV Receiver (too large). • The wrong type of IEEE  cable has been used. Obtain a -pin
type or a  pin to  pin adaptor cable from an electronic or computer
store.
• An IEEE  device has been plugged in but does not appear
in the Device Selection menu (not discovered).
• The IEEE  connection to the HDTV Receiver or another device
is not secure or is loose.
• The IEEE  device is not powered on.
• Some device in the IEEE  chain is not powered-turn on all
the devices.
• The device discovery can take as long as a minute to initiate.
• IEEE  cable is too long (maximum of  feet between devices).
• The IEEE  device uses an incompatible protocol and cannot
be discovered.
• Cannot see a picture from a DV Camcorder. •Go to Device Selection menu and select analog connection.
•Connect the DV Camcorder to analog input (for example, Input-).
Then go to Setup in the main menu, select Edit NetCommand, and
select Change. On the Change screen select the camcorder. On the
Name screen, check Analog Connection. Then select the device and
on the following screen, select which analog input was used, and
check audio and/or video.
• All IEEE  devices disappear. •When connecting the devices, there must always be a device at the
end. Connected devices must not be in a loop that returns to the
HDTV Receiver.
•Disconnect all the cables and devices from the HDTV Receiver.
Replace them one by one to locate the problem device or cable.
•Use System Reset (front control panel).
• Cannot rediscover a deleted IEEE  device. •The device has been disconnected. Plug it in.
•The device is unchecked in the Review screen. Go to Setup in
the Main menu, select Edit NetCommand, then select Review. Verify
the device is checked.
•Remove IEEE  plug. Go to the Edit NetCommand menu.
Delete the IEEE  device. Plug the device in again so it can
be discovered again.
• DVCR analog/digital problems. •If the tape is currently playing but no picture displays, you may
have a mismatch of the media with the display. Press the DEVICE
key to display the Device Selection menu. Press ENTER for the
DVCR device. From the pop up box, if digital is selected, try analog,
or if analog is selected, try digital.
• D-VHS recordings for digital cable have drop-outs (loss of
picture or sound).
•Digital cable signals on IEEE  can exceed the standards
established for D-VHS and this can cause some droputs.
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi HD5000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi HD5000 in the language / languages: English as an attachment in your email.

The manual is 1,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info