30505

Mitsubishi HD5000 Manual

19
Zoom out
Zoom in
Previous page
1/24
Next page
19
• When a Device is selected from the Device Selection
menu, the screen is blue (no signal source).
• Make sure the selected device is turned on.
• From the Edit NetCommand® menu select Review then check the
Review screen to see if inputs match the actual connections on the
HDTV Receiver. If they do not match, either change the
actual connections, or select Change on the EditNetCommand menu
to change the HDTV Receiver’s Memory for the connection.
• The Device does not respond to key presses from the
remote.
• Remote has not been setup for NetCommand use. See the
HD- Owner’s Guide.
• The incorrect manufacturer was selected during setup. Select
Change on the Edit NetCommand menu and then select the device
to display the manufacturer selection. Change if necessary.
• The device is not supported.
• The requested function is not supported by NetCommand.
Verify the function supported.
• The IR emitter is incorrectly placed. Make sure the IR
emitter is facing the IR sensor in the device.
• The IR emitter is not plugged into the IR emitter Output
NetCommand.
• The IR emitter is facing the HDTV Receiver IR Sensor,
causing double signals. Be sure that the IR emitter cannot “see” the
HDTV Receiver IR Sensor.
• The A/V Receiver is the selected audio source but
there is no sound.
• Check to see if the A/V Receiver power is turned on. After the
power is turned on, redisplay the Device Selection menu and press
ENT(er) to allow NetCommand to correctly select the A/V Receiver
input.
• From the Edit NetCommand select Review. Check the Review screen
to see if the A/V Receiver inputs for the selected configuration match
the actual connections on the A/V Receiver. If they do not match,
either change the actual connections, or select Change on the Edit
NetCommand menu to change the HDTV Receiver memory for the
connection.
• The Speaker icon or A/V Receiver icon is grayed
out and not selectable.
• Select Change from the Edit NetCommand menu, and then
select the device. Once the Connection screen is displayed,
check if the audio checkbox is selected for the HDTV Receiver
input and/or AVR input.
• Devices are grayed out in the Device Selection menu
or the PIP Selection menu.
• A recording is in progress requiring the use of Monitor Out.
Cancel the recording to select the device.
• Digital devices (Ant-DTV and  devices) and devices with
scanning rate of p or i cannot display in the PIP or
POP.
• Cannot see the A/V Receiver menu. • Normally, the A/V Receiver is not connected to any
input of the HDTV Receiver. To check the A/V Receiver
menu, temporarily plug into an unused input of the HDTV Receiver.
Then after selecting Review from the Edit NetCommand menu,
turn the input On to view the A/V Receiver menu.
• The REC button is not working, or, on the Transport
menu the record key is grayed out and not available.
• The device does not support recording, such as a DVD player.
• Recordings can not be initiated from the Transport menu when
the device is an IEEE  device. To record to an IEEE 
device, change the HDTV Receiver to the ANT-DTV or source
device for the recording and press the REC key. The Record
menu displays allowing setup of a recording.
• Excessive digital artifacts. • The IEEE  cable is too long (maximum of  feet between
devices.)
•There may be a slow device in the middle of the IEEE 
network. Move the slow devices to the end so that connections
for faster devices do not pass through them.
Problem Possible Solution
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi HD5000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi HD5000 in the language / languages: English as an attachment in your email.

The manual is 1,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info