549872

Mitsubishi HC8000D Manual

24
Zoom out
Zoom in
Previous page
1/55
Next page
EN-24
Viewing computer images (continued)
To stop projecting:
9. Press the POWER button on the projector or the STANDBY ( ) button on the remote control.
• Aconrmationmessageisdisplayed.
• Tocanceltheprocedure,leavetheprojectorforawhileorpresstheMENUbutton.
10. Press the POWER button on the projector or the STANDBY ( ) button on the remote control again.
• Thelampgoesoutandtheprojectorgoesintoastandbymode.Inthisstandbymode,theSTATUSindicator
blinks green.
11. Wait about 2 minutes.
• Duringthisperiodof2minutesinthestandbymode,theintakefanandexhaustfanrotatetocoolthelamp.
• Thelampcan’tbelitagainfor1minuteafterturningofftheprojectorforsafetypurpose.Itwilltakeanother1
minute for the STATUS indicator to go out. If you want to turn on the projector again, wait until the indicator
goes out, and then press the POWER button.
• Theairoutletfansrotatefasterasthetemperaturearoundtheprojectorrises.
• DonotunplugthepowercordwhiletheSTATUSindicatorisblinking.Unpluggingthepowercordimmediately
after use may cause a lamp breakdown.
• Thoughthefanmakesloudsoundsduringcooling,suchsymptomisnotamalfunction.
12. Unplug the power cord from the outlet.
• ThePOWERindicatorwillgoout.
• Ifthepowercordshouldbeunpluggedaccidentallywhileeithertheairinletfanortheairoutletfansare
operating or the lamp is on, allow the projector to cool down for 10 minutes with the power off. To light the
lamp again, press the POWER button. If the lamp doesn’t light up immediately, repeat pressing the POWER
button two or three times. If it should still fail to light up, replace the lamp.
• Coverthelenswiththelenscaptoprotectitfromdust.
AUTO POSITION button
When the image supplied from the computer is displaced, carry out the following procedure.
1. Display a bright image (such as a full-screen display of the Recycle Bin window).
2. When the screen saver has been enabled, disable it.
3. Press the AUTO POSITION button.
The projector automatically makes optimum positional settings for the input signal.
• IftheimageisnotprojectedinthecorrectpositionevenafteryoupresstheAUTOPOSITIONbuttonseveral
times, change the settings in the SIGNAL menu to put the image in the correct position. (See page 34.)
• Whenyoucarryoutthisprocedurewithadarkimage,theimagemaybedisplaced.
When connecting to a notebook computer:
When the projector is connected to a notebook computer, images may not be projected in some cases. In such
cases, set the computer so that it can output signals externally. The setting procedure varies depending on the type
of the computer. See the instruction manual of your computer.
Example of the setting procedure for external output
Press the [Fn] key and any of the keys [F1] to [F12] at the same time. (The key to be pressed depends on the type of
the computer you use.)
Setting of the resolution
If the resolution of the computer doesn’t match with that of the projector, projected images may be obscured. Ensure
that their resolutions are the same (see page 53). For the method to change the output resolution of the computer,
contact the manufacturer of the computer.
… 24 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi HC8000D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi HC8000D in the language / languages: English as an attachment in your email.

The manual is 7,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info