727618

Minimoka CM-4758 Manual

21
Zoom out
Zoom in
Previous page
1/32
Next page
Note:
If the following warning appears on the display, the water
tank must topped up before the next drink is dispensed.
Otherwise further function is not possible.
Before inserting the water tank, make sure that it is dry
on the outside. Wipe the water tank shaft dry also before
inserting the water tank.
Filling the coffee bean container:
- Fold back the lid of the coffee container (K).
- Fill the container with fresh coffee beans.
- Then close the container again.
Use:
- Connect the appliance to the mains.
- Turn the appliance on, by pressing the on/off button
andholdingitdownbriey.Duringtheheatingprocedure
(approx.30seconds)thefollowingdisplayashes.
- When the operating temperature has been reached,
the coffee machine automatically performs a rising cycle.
Watermayowhereintothedriptray.
-When the rising cycle is completed, the coffee machine
is ready to use. The following displays light up during
initial start-up:
Determining the water hardness
Beforeusingthecoffeemachineforthersttime,it
should be set to the appropriate water hardness for
your region. You can determine the water hardness with
the help of the test strip (18) supplied with the coffee
machine.
Proceed as follows:
- Dip the test strip into cold water for 1 second and shake
off the excess water. After approximately 1 minute, the
water hardness can read from the pink-coloured areas.
Menu settings
The menu function must be accessed to undertake va-
rious settings – for example, to set the determined water
hardness level.
To do this, press buttons 2 and 3 simultaneously for
approx. 3 seconds.
Thesymboldisplaywillbrieylightupasablinkingline,
then the display will change to the current settings. The
following parameters can be set:
• Water tank illumination via button 2
• Water hardness level via button 3
• Coffee temperature via button 4
• Switch-off time via button 5.
•Savetheentriesandquitthemenubyconrmingwith
OK (button 6). If you do not press OK, the program will
automatically return to the operating mode after approx.
60 sec. without saving the new settings.
Setting and storing the water hardness:
- Switch to the menu function by simultaneously pressing
buttons 2 and 3 for approx. 3 seconds. The function
displaysofthemenuwillashrstinablinkingline,then
the current settings will be displayed.
Then press key 3 repeatedly until the required hardness
degree is set.
The image below shows the displays for the 4 possible
hardness degree settings.
Store the input by pressing “OK” (button 6). All function
displaysofthemenuashforapprox.3secondstocon-
rm.Theappliancethenreturnstothenormaloperating
mode.
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Minimoka CM-4758 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Minimoka CM-4758 in the language / languages: English, Spanish as an attachment in your email.

The manual is 2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info