Manual Milwaukee 5262-20 (page 7 of 24) (English, French, Spanish)

641640

Zoom out

Zoom in

1/24



Core bits are useful for drilling larger holes for

conduit and pipe. MILWAUKEE Thin Wall Core

Bits have heat-treated steel bodies with durable

carbide tips. These core bits are specially designed

for fast, accurate drilling with combined hammering

and rotary action.

1. Clean and lubricate the

threads on the adapter

and core bit to make later

removal easier. Screw the

threaded end of the adapter

into the rear of the core bit.

 For core bits 1- 1/4"

and larger, push the guide

plate onto the pointed end of

the center pin. Insert the center

pin and guide plate assembly

into the core bit. Be sure the

small end of the center pin is

securely placed into the hole

in the center of the core bit.

2. Insert the adapter into the nose

of the tool as described in “In-

stalling Bits”. Set the hammer/

drill shift knob to hammering

with rotation.

3. Press the center pin firmly

against your center mark, hold

the tool rmly and pull the trigger.

 If a center pin and guide

plate are not available, use a template or notched

board to start the hole.

5. After drilling to about the depth of the core bit

teeth, remove the center pin and guide plate from

the core bit. Resume drilling.

6. To change the core bit, hold the tool upwards,

pointing it away from your body, and run it briey

in forward to loosen the core bit from the adapter.

 To make holes deeper than 3", remove the

core bit, break and remove the core. Resume drilling.

Adapter

Core

Bit

Center

Guide

Plate

Clean

and

lubricate

threads







Always allow the motor to

come to a complete stop be-

fore using the control switch.

For  (clockwise) rota-

tion, push the control switch

to the left side of the tool.

Check the direction of rotation

before use.

For  (counterclock-

wise) rotation, push the con-

trol switch to the right side of

the tool. Check direction of

rotation before use.



1. To  the tool, grasp the handle rmly and pull

the trigger.

2. To  the speed, increase or decrease the

pressure on the trigger. The further the trigger

is pulled, the greater the speed.

3. To  the tool, release the trigger. Make sure

the tool comes to a complete stop before laying

the tool down.



The lock-on button holds the trigger in the ON posi-

tion for continuous full speed use.

1. To lock the trigger, hold in the lock button while

pulling the trigger. Release the trigger.

2. To unlock the trigger, pull the trigger and release.

The lock button will pop out.



Position the tool, grasp the handles rmly and pull

the trigger. Always hold the tool securely using

both handles to maintain control. This tool has

been designed to achieve top performance with

only moderate pressure. Let the tool do the work.

If the speed begins to drop off when drilling large

or deep holes, pull the bit partially out of the hole

while the tool is running to help clear dust. Do not

use water to settle the dust since it will clog the bit

utes and tend to make the bit bind in the hole. If

the bit should bind, a built-in, non-adjustable slip

clutch prevents the bit from turning. If this occurs,

stop the tool, free the bit and begin again.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Milwaukee 5262-20 in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 2,17 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Milwaukee 5262-20 Manual

Product: