Manual Milwaukee 5262-20 (page 6 of 24) (English, French, Spanish)

641640

6

Zoom out

Zoom in

Previous page

1/24

Next page

6

ASSEMBLY



1. Loosen the side handle by unscrewing the side

handle grip until the side handle rotates freely.

2. Rotate the side handle to the desired position.

3. Tighten the side handle grip securely.



1. Press in the clamping lever.

2. Slide the depth gauge rod backward or forward

until it is set for the desired depth.

 The drilling depth is the distance between

the tip of the bit and the tip of the rod.

3. Release the clamping lever.



Only use accessories with SDS or SDS Plus shanks.

Be sure that the shank of the bit is clean. Dirt par-

ticles may cause the bit to line up improperly. Do not

use bits larger than the maximum recommended

capacity of the drill because gear damage or mo-

tor overloading may result. For best performance,

be sure that the bit is properly sharpened and the

shank is lightly greased before use.

1. Insert the bit or chisel into the nose of the tool.

2. Rotate bit slowly until it aligns with the locking

mechanism.

3. Push bit into tool until it locks.

4. Check that the bit is locked properly; it should

be possible to pull the bit back and forth slightly

(about 1/4").

5. To remove bits and chisels,

pull bit holder release collar

toward the rear of tool and

remove bit.

 Use caution when

handling hot bits and chis-

els.

OPERATION



These MILWAUKEE Rotary Hammers have three

settings: rotation only, rotary hammer, and ham-

mer only. Always allow the motor to come to a

complete stop before changing the mode selection

to avoid damage to the tool.

1. For rotation only, press in

the selector release button

and turn the selector lever

so the arrow on the lever

points to the twist drill

symbol.

2. For rotary hammering, press in the selector

release button and turn the selector lever so

the arrow points to the hammer and twist drill

symbol.

3. For hammering only, press in the selector release

button and turn the selector lever so the arrow

points to the hammer symbol.

4. To freely rotate the bit to the desired angle for

hammering only, press in the selector release

button and turn the selector lever to the

symbol. Then, follow step 3.

 To engage the hammering mechanism,

maintain pressure on the bit. When pressure on

the bit is released, the hammering action will stop.

WARNING 

      -



-



WARNING 





WARNING 

-

  

WARNING 

-







WARNING 

      



WARNING 





Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

Register

Register getting emails for Milwaukee 5262-20 at:

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Milwaukee 5262-20 in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 2,17 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info