738662
44
Zoom out
Zoom in
Previous page
1/146
Next page
16 Advanced operations
reception of a correct CTCSS/DCS signal, with CTCSS/DCS incor-
rect, etc.). For details about the BCLO operation please refer to the
paragraph 5.6.b
7.2 Handsfree transmission (VOX)
VOX (Voice Operated eXchange) is a device that allows you to automati-
cally switch the transmission in hands free mode just by speaking in the
built-in microphone of a headset (not provided with the unit) connected
to your transceiver. Once you have finished to talk, the VOX automatically
switches the radio on reception.
Ensure that the headset with microphone you are going to use is
suitable to your transceiver as stated in the paragraph 9.1
7.2.a Headset Connection
1) With a suitable screwdriver, unscrew the screw that holds the cover
cap of the accessory connector (item [7] of the paragraph 3.3)
2) Keep the cover cap in a safe place and connect the headset/micro-
phone to the accessory connector (for details about the contacts
layout please refer to the paragraph 9.1.a).
In order to avoid damages to the device, put the cover cap in its
place again when the accessory connector is not used.
7.2.b Enabling/disabling VOX
1) Ensure that the headset is properly connected and that the headset’s
built-in microphone is located close to the side of your mouth.
2) Switch on the radio on keeping pressed the FUNC button.
3) When the device is switched on, release the button.
7.2.c Adjusting VOX sensitivity
1) Enable the VOX as described above
2) Briefly press the FUNC button to select one of two VOX sensitivity
levels (high/low).
3) Perform some tests in order to ensure a stable transmission when
speaking with a normal voice level, but avoiding accidental transmis-
sions.
We recommend to set just the minimum sensitivity as possible.
A too high value could cause accidental transmissions, espe-
cially in hi-noise environments.
The transceiver isn’t provided with any indication of LOW/HIGH VOX
sensitivity
PTT button is disabled during VOX operation.
7.3 Confidential Communications (scrambler)
Your transceiver could have been programmed to use the scrambler
when necessary. This is a device that make your communications unin-
telligible to normal receivers/transceivers, but perfectly clear to the other
radios of your network, that obviously must belong to the HPx06 family
(i.e. equipped of the same type of scrambler).
To enable the scrambler:
1) Ensure that the other party enables his/her scrambler too.
2) Simultaneously and briefly press the MON and FUNC buttons. The
device will send a high-pitched beep to confirm that the scrambler is
enabled.
To disable the scrambler:
English
ISTR106_int 26-09-2003 9:47 Pagina 16
44


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Midland Alan HP106 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Midland Alan HP106 in the language / languages: English, German, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info