738663
37
Zoom out
Zoom in
Previous page
1/146
Next page
Setup 9
To remove the antenna:
1) Execute the above-mentioned step 1.
2) Unscrew the rubber ducky antenna rotating it counterclockwise and
remove it.
Leave the antenna fitted on the radio. You can’t communicate
without it. Moreover, transmitting without the antenna (or with a
damaged antenna) may damage the TX output final stage. Use
the supplied antenna only.
The supplied antenna is broadband type and covers the whole spec-
trum, so it doesn’t need any alignment procedure.
4.3 Installing/removing the battery pack
To install the battery pack (please refer to the drawing):
1) Direct the front part of the transceiver
downwards. Hold the transceiver’s
body with one hand and the battery
pack with the other. Put the battery
pack onto the lower part of the trans-
ceiver’s battery slot as shown.
2) Firmly push the battery pack toward
the upper part of the transceiver’s bat-
tery slot until you will hear a mechani-
cal snap (click), meaning that the bat-
tery pack is steadily locked in its posi-
tion.
To remove the battery pack:
1) Press and hold in the direction shown
by the arrow the battery release button
located in the back of the battery pack.
2) Ensure that the battery pack is unloc-
ked, keep the button pressed and
gently pull the battery pack away from
the upper edge of the transceiver’s bat-
tery slot (the opposite operation of the
previous step 2).
3) Remove the battery pack by separating it from the transceiver’s
body.
For details about the battery pack charge and the battery chargers to
make use of please see the paragraph 4.5.
4.4 Installing/removing the belt clip
The supplied belt allows you to
hang the transceiver up to your
belt or jacket when you are not
using the radio and you are just in
stand-by condition (ready to recei-
ve calls).
To fit the belt clip onto the trans-
ceiver’s body just gently slide the
clip into the appropriate guides
located in the transceiver’s back
(battery slot) until it firmly locks.
English
1slide down
2push down
1push down
2let up
1slide down
3slide over
2press
ISTR106_int 26-09-2003 9:47 Pagina 9
37


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Midland Alan HP 406 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Midland Alan HP 406 in the language / languages: English, German, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info