588175
9
Zoom out
Zoom in
Previous page
1/10
Next page
Connect Panel with Swing Motor Wire Connector (white) and Remote Controller Wire Connector
after passing through a hole. (Chart 18)
Hole
Swing Motor Wire
Chart 18 Swing Motor Wire
Swing Motor Wire
Installation Screws
Nut Cap
Chart 19 Installation sequence of screws
Confirm the wires are not nipped between the panel and the Indoor Unit, or the panel and the
ceiling. Then fasten the screws according to the following. (chart 19)
1) Fix the panel at central point temporarily.
2) Confirm and adjust the position.
3) Fix left side of panel (from to ) temporarily.
4) Fix right side of panel (from to ) temporarily.
5) Confirm the installation position.
6) Fasten the , , , , screws tightly.
After tightening Panel Screws, install two screw caps to the screws at side of Air Outlet. (chart 19 )
A
7
6
5
4
3
2
1
Lead Swing Motor Wire into a hole. (Chart 18)
Hang the Strip Hook of Inlet Grille to the hole in the middle of
Indoor Unit Air Inlet. (Chart 20)
Hole
Strip Hook
Chart 20 Hang the Strip Hook of Inlet Grille
NOTICES FOR BENDABLE PIPE
O
The bending angle should not exceed 90 .
Bending position is preferably in the bendable pipe. The larger the better it is.
Do not bend the pipe more than three times.
BEND THE CONNECTING PIPE OF SMALL WALL THICKNESS
Cut out a desired concave at the bending part of the insulating pipe. Then expose the pipe (cover
it with tapes after bending).
To prevent collapsing or deforming, please bend the pipe at its biggest radius.
Use bender to get a small radius pipes.
USE THE MARKET BRASS PIPE
Be sure to use the same insulating materials when you buy the brass pipe.
2. Locate The Pipe
Drill a hole in the wall (suitable just for the size of the wall conduit, 90mm in general), then set on the
fittings such as the wall conduit and its cover.
Bind the connecting pipe and the cables together tightly with binding tapes. Do not let air in, which
will cause water leakage by condensation.
Pass the bound connecting pipe through the wall conduit from outside. Be careful of the pipe
allocation to do no damage to the tubing.
Connect the pipes.
Then, open the stem of stop values of the outdoor unit to make the refrigerant pipe connecting the
indoor unit with the outdoor unit in fluent flow.
Be sure of no leakage by checking it with leak detector or soap water.
Cover the joint of the connecting pipe to the indoor unit with the soundproof / insulating sheath
(fittings), and bind it well with the tapes to prevent leakage.
3.
4.
5.
6.
1)
2)
3)
FLARING
90 +4
4
5
+
2
A
90
lean crude burr
Chart 28
Chart 29
Outside-
diameter
A (mm)
max
min
F6.35mm
F9.53mm
F12.7mm
8.7
12.4
15.8
8.3
12
15.4
1. Cut a pipe with a pipe cutter.
2. Insert a flare nut into a pipe and flare the pipe.
Table 1
EXPEL THE AIR
REFRIGERANT PIPE CONNECTING
FASTEN THE NUT
Put the connecting tubing at the proper position,
wrench the nuts with hands then fasten it with a
wrench. (Refer to Chart 30)
Chart 30
7
10
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Midea MCB09HRN2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Midea MCB09HRN2 in the language / languages: English as an attachment in your email.

The manual is 0,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Midea MCB09HRN2

Midea MCB09HRN2 User Manual - English - 22 pages

Midea MCB09HRN2 Installation Guide - Dutch - 5 pages

Midea MCB09HRN2 User Manual - Dutch - 9 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info