658483

Midas VeniceU U16 Manual

101
Zoom out
Zoom in
Previous page
1/122
Next page
Routing 91
VeniceU
Operator Manual
The submix is now set up. The group level can be used to control the overall level of
the channels (retaining their relative levels), mute the submix output or solo the
submix signal.
Note: Muting the submix is not the same as muting the channels. Aux sends and
other group sends will remain active.
• Common EQ/processing Often, it is either too expensive or undesirable to apply
processing to each channel individually (for example, compression on a whole choir,
graphic EQ on a number of microphones, etc.). Setting up a submix as above, the
signal is grouped together. Now the desired processor can be inserted into the group
inserts applying the processing to all of the submix channels (in their relative levels).
• Alternative outputs For example, you were mixing a number of speakers in a
venue and each needed a different level and processing.
Route the desired channels to any group or master output as necessary. Make sure
the group is not routed to the main outputs. The group outputs should be wired into
the necessary amplification and the insert points into any necessary processing (for
example, delay, EQ, etc.).
The levels are now individually controllable.
MON mode
The group-aux changeover switch on each group (see “Group-aux changeover” on
page 60) should be depressed (in the on position) so that the group fader controls the
aux bus signal.
Channel signal should be sent to the aux, as required, and the aux sends should usually
be configured to pre-fader. The console group output sockets should be wired into the
necessary amplification and the insert points into any necessary processing (for
example, EQ, etc.).
The monitor levels are now individually controllable on the group faders.
Dual FOH/MON Mode
The group-aux changeover switch on each group (see “Group-aux changeover” on
page 60) should be depressed (in the on position) so that the group fader controls the
aux bus signal for monitors or released (in the off position) so that the group fader
controls the group bus signal for FOH. The usage in this split mode can be any
combination of the above!
Note: When the group-aux changeover switch is depressed, control over the groups is
performed by the aux controls and hence, and group outputs may still be used.
Submixes could be used by connecting the aux output sockets on the rear of the
console to four unused stereo input channels and routed to the left and right master
buses.
… 101 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Midas VeniceU U16 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Midas VeniceU U16 in the language / languages: English as an attachment in your email.

The manual is 5,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info