658483

Midas VeniceU U16 Manual

100
Zoom out
Zoom in
Previous page
1/122
Next page
90 Appendix C: Application Notes
VeniceU
Operator Manual
There are a number of solutions to this problem:
• Reduce the amplifier’s input attenuators to a level where the amplifier and
console clip at the same point.
For example, the input sensitivity is 0dBu, setting the input attenuator on the
amplifier to -21dB would mean that the console would clip at the same time as the
amplifier. So, operating the console sensibly the amplifier should never be clipped.
The console LED meters will also accurately show the available headroom left in the
entire system.
-21dB may not be a sensible level to set as many operators choose not to run the
output of the console so high. That is personal choice.
• Run the output of the console at a level below 0dBu.
This solution means that you won’t get full benefit of the console, and may suffer a
reduced signal to noise ratio, especially when running over long signal cables. But
the amplifiers should be saved from clipping.
As with many things in the audio world, use your ears. If something sounds distorted,
do the following:
Routing
The flexible routing of the VeniceU allows the console to operate as both a FOH and
monitor console, or as a combination of both. For operators that haven’t got a great
deal of experience, here are a few helpful guidelines.
FOH mode
The group-aux changeover switch on each group (see “Group-aux changeover” on
page 60) should be released (in the off position) so that the group fader controls the
group bus signal.
Uses for groups vary, but include:
• Submixes Submixes are a common way of saving time (and possibly
embarrassment) when using a large number of microphones at once. For example,
multiple microphones for choirs, drum kits/percussion, orchestras, etc.
The channel to be submixed should be routed to the group and any aux sends ONLY
(that is, not to the master L-M-R). The fader is, as normal, used to set the relative
level between the channels in the submix. The group chosen for the submix should
then be routed to the master L-M-R and panned as required.
Problem Action
Input gain is too high Lower input gain
EQ has too much boost Disable EQ
EQ has too much cut and has a high
input gain
Disable EQ
There is too high a level entering the
inserted processor
Disable insert
The loudspeaker controller or amplifiers
are clipping
Check clipping indicators on amplifiers,
etc.
… 100 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Midas VeniceU U16 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Midas VeniceU U16 in the language / languages: English as an attachment in your email.

The manual is 5,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info