658461

Midas M32 Manual

39
Zoom out
Zoom in
Previous page
1/61
Next page
39 M32 DIGITAL CONSOLE User Manual
The BALANCE push encoder adjusts the balance between anger and reverb.
Low frequencies can be excluded with the LO CUT push encoder, and the MIX
push encoder adjusts how much of the eect is added to the signal. SPEED,
DELAY and DEPTH adjust the rate, delay and modulation depth of the anger.
FEEDback can be adjusted by positive and negative amounts. The LFO PHASE
between the left and right channels can be oset by up to 180°. The PREDELAY
push encoder determines the delay before the reverb aects the signal. The
DECAY push encoder adjusts how quickly the reverb fades. SIZE controls the
size of the simulated space (room, cathedral, etc.). The DAMPING push encoder
determines the decay of high frequencies within the reverb tail.
Delay + Chorus
This combination eect merges a user-denable delay (echo) with a studio-
quality chorus, sure to fatten up even the skinniest track. Uses only one FX slot.
Inspired by the TC Electronic D-Two.
The TIME push encoder adjusts the delay time, and the PATTERN push encoder
sets the delay ratio for the right channel and negative values activate a cross
feedback between the two channels. The FEEDHC push encoder adjusts the delay
high-cut frequency, while FEEDBACK adjusts the number of repeats. The X-FEED
control allows you to send the delay sound to the chorus eect. The BALANCE
push encoder adjusts the ratio between delay and chorus. SPEED, DELAY and
DEPTH adjust the rate, delay and modulation depth of the chorus. The right
channel LFO PHASE can be oset by up to 180°, and WAVE adjusts the chorus
character by shaping the LFO waveform from sine wave to triangular wave. Use
the MIX push encoder to blend the aected signal with the dry sound.
Delay + Flanger
This handy dynamic duo blends the ‘whoosh’ of soaring jet planes with classic
delay, and can be adjusted from mild to wild. This combination eect only takes
up one FX slot. Inspired by the TC Electronic D-Two.
The TIME push encoder adjusts the delay time, and the PATTERN push encoder
sets the delay ratio for the right channel and negative values activate a cross
feedback between the two channels. The FEEDHC push encoder adjusts the delay
high-cut frequency, while FEEDBACK adjusts the number of repeats. The X-FEED
control allows you to send the delay sound to the chorus eect. The BALANCE
push encoder adjusts the ratio between delay and chorus. SPEED, DELAY and
DEPTH adjust the rate, delay and modulation depth of the chorus. The right
channel LFO PHASE can be oset by up to 180°, and FEED (positive and negative
amounts) adjusts the feedback eect. Use the MIX push encoder to blend the
aected signal with the dry sound.
Modulation Delay
Combining echo and chorus (and in this case, reverb too) is the domain of the
Modulation Delay. By combining the two, you can get the best of both worlds in
one, dreamy-sounding eect.
The controls are separated onto two layers; layer one for the delay, and layer
two for the chorus. Use Balance to sweep between how much of either eect
is present in the output signal. Navigate to layer two by using the navigational
control buttons. Use the PAR / SER function to switch between Parallel and
Serial modes. In Parallel mode the input signal is routed both to the modulated
delay and the reverb inputs. In Serial mode the modulated delay output is routed
to the reverb input. (When balance is set to -100 there is no audible dierence
between the two modes since in this case only the modulated reverb is audible.)
On layer one Time adjusts the time of the delay, whereas Feed controls how
many echoes follow the input signal. Lo Cut and Hi Cut are, as the names
suggest, low cut and high cut lters for the aected signal. On both, Mix dictates
how much of the aected signal is sent to the output bus.
On layer two Depth controls the depth of the chorus eect, Rate controls the
speed of the modulation, and Decay controls the length of time after the initial
signal where the eect is present. Damping reduces the level of the higher
frequencies in the output.
The type of reverb can be switched by pressing either of the third, fourth or fth
push encoders.
Dual Graphic EQ / Stereo Graphic EQ / Dual TruEQ /
Stereo TruEQ
… 39 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Midas M32 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Midas M32 in the language / languages: English as an attachment in your email.

The manual is 9,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info